← Espace Renault Espace repair manuals →

Renault Espace IV (2008): Checking and Adjusting Front Wheel Alignment

Wheel alignment on the Espace IV can only be done on an alignment machine. First check the condition of the suspension and steering, then measure the angles and adjust whatever the design allows. Toe is usually adjusted by changing the length of the tie rods. On most suspensions of this type, camber and caster are set by the design and can be corrected only if adjustment elements are present. If the measurements are out of tolerance and the suspension is in good condition, look for deformation of the body or subframe.

DifficultyHard Time1-1.5 hours Steps12

Diagram: where the tie rod with lock nut is and how to change its length when adjusting toe

View from below, from under the wheel archHub with armTurn the rod: length changes5Steering rack1Tie rod2Lock nut3Rack boot4Tie rod end with ball stud6Wrench holds the lock nutTap to enlarge
  1. 1Tie rod: the metal rod from the rack to the wheel. Turn it to change its length when adjusting toe. Turn both rods evenly so the steering wheel stays straight.
  2. 2Lock nut on the tie rod thread. Loosen it before adjusting, tighten it afterwards while holding the rod from turning, then recheck the toe.
  3. 3Steering rack boot: the ribbed sleeve the tie rod comes out of. Make sure it does not twist when the rod is turned.
  4. 4Tie rod end with a ball stud: connects the rod to the wheel arm. If it has play, replace it first.
  5. 5Steering rack: the tie rods go out from it. Before measuring, set the steering wheel straight and lock it.
  6. 6Wrench on the lock nut: used to loosen and tighten the nut while the rod is held from turning.

Parts

4
№Part
01 Tie rod endsif needed, based on suspension inspectionFind on Amazon →
02 Tie rodsif needed, based on suspension inspectionFind on Amazon →
03 Ball jointsif needed, based on suspension inspectionFind on Amazon →
04 Control arm bushingsif needed, based on suspension inspectionFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 3 more. See manuals →

Step by step

12 steps
  1. Prepare the vehicle: set tire pressure to the value on the door pillar placard, use matching tires with equal wear, leave the trunk empty, and keep the fuel level about the same as in normal use.
  2. Drive the vehicle onto the alignment rack or lift with level turntables, apply the parking brake, and make sure the turntables are unlocked.
  3. Check for play: ball joints, steering rack tie rod ends and rods, control arm bushings, strut top mounts, wheel bearings. Replace any part with play first, otherwise the adjustment is pointless.
  4. Inspect the wheels and tires: deformation, uneven wear (sawtooth wear on the edge indicates incorrect toe or camber).
  5. Mount the alignment machine sensors or targets on the wheels and perform wheel runout compensation according to the machine's instructions.
  6. Settle the suspension (bounce the body), set the steering wheel exactly straight, and secure it with the steering wheel lock.
  7. Measure camber, caster, and toe for each wheel. Compare them with the Espace IV tolerances in the machine's database. The permitted difference between the left and right sides is also important.
  8. Toe adjustment: loosen the lock nuts on the tie rods and turn the rod to change its length. Turn both rods equally so the steering wheel stays straight. Watch the condition of the boots so they do not get twisted.
  9. If the machine shows camber or caster out of tolerance, check the control arms, subframe, and mounting points for deformation. Where adjustment is provided, it is done by shifting the control arm or subframe mounting. Then check the toe again.
  10. Tighten the tie rod lock nuts while holding the rod to keep it from turning. Use the torque specified by the manufacturer. Recheck the toe after tightening.
  11. Tighten the wheel bolts with a torque wrench in a crisscross pattern to the torque specified by the manufacturer.
  12. Take a test drive: the steering wheel should sit straight when driving straight, and the vehicle should not pull to one side. Recheck the steering wheel position.

Common mistakes and warnings

  • Steering and suspension affect safety
  • If you have no experience with an alignment machine, leave the adjustment to a repair shop
  • Check the angle values and torque specifications against the manufacturer's specifications for this version and wheel size
Spotted a mistake? Tell us →

Our articles

More articles →