Autopapyrus · Renault Sandero 1.2 16V D4F 732 (2015)
https://autopapyrus.com/catalog/renault/sandero/guides/replacing-the-evaporative-emission-purge-valve/
https://autopapyrus.com/catalog/renault/sandero/guides/replacing-the-evaporative-emission-purge-valve/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Renault Sandero 1.2 16V D4F 732 (2015): Replacing the Evaporative Emission Purge Valve
The EVAP canister purge valve is a small solenoid valve that, on command from the engine control unit, feeds fuel vapor from the charcoal canister into the intake. If it sticks, you may notice a rough idle, hesitation, occasional stalling, a fuel smell, and EVAP system fault codes. The job needs no special tools: you disconnect the electrical connector and two hoses.
Diagram: where the canister purge valve is and how to remove the connector and hoses
Tap to enlarge
- 1Purge valve: compact black body with two nozzles. Remove it from its holder and replace it with the new one.
- 2Valve electrical connector: press the latch and unplug it.
- 3Hose to the intake: squeeze the clamp or retainer with pliers, pull the hose off and plug it right away.
- 4Hose from the canister: squeeze the clamp the same way, remove it and plug it. Fit it to the same nozzle on the new valve.
- 5Canister: a cylindrical can in the right front wheel arch, with a hose running to the valve.
- 6Rubber mount or bracket: pull the valve out of the mount or undo the fastener without force.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | EVAP canister purge solenoid valve forFind on Amazon → | AlternativesBoschPierburgHella |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
4
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
10 steps- Shut off the engine and let it cool down. Open the hood and disconnect the negative battery terminal.
- Locate the valve: it is a small cylindrical or rectangular part with a two-pin electrical connector and two nipples that the fuel vapor hoses connect to. It is in the engine bay, on the line between the canister and the intake tract. The canister is located in the right front wheel arch.
- To make reassembly easier, take a photo of how the hoses are routed and mark which hose is connected to which nipple (the valve nipples are usually different, so you must not mix them up during installation).
- Press the locking tab and disconnect the valve's electrical connector.
- Disconnect both hoses from the valve nipples: squeeze the quick-release clips or clamps with pliers and pull the hoses off. Immediately insert plugs or caps into the hoses so no dirt gets inside.
- Remove the valve from its holder or bracket: pull it out of the rubber mount or undo the fasteners. If the fastener is threaded, the tightening torque is low and no torque wrench is needed: just tighten until snug, without force.
- Inspect the hoses and nipples. Cracks, oil traces or softened rubber are a reason to replace the hose at the same time as the valve.
- Install the new valve in reverse order: secure it in the holder, remove the plugs, push the hoses onto the same nipples as before until they click or are secured with the clamp, and connect the electrical connector.
- Reconnect the negative terminal, start the engine, and check that the idle is smooth. Listen for a light clicking sound, which indicates the valve is working.
- If the Check Engine light was on, clear the fault codes with an OBD scan tool and check whether the code returns after a drive.
Common mistakes and warnings
- Work away from open flames and sparks, as fuel vapor is flammable
- Do not leave the hoses open, or dirt will get into the system
- Exact tightening torques for the valve and canister fasteners are not given in publicly available sources: tighten threaded connections moderately and verify the values against the manufacturer's specifications
- If the rough idle persists after replacement, the cause may be the canister itself, the hoses, or another fault, in which case it is best to have the car diagnosed at a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Renault
Louis Renault (1877–1944) was interested in electricity and mechanics from an early age, and he was destined to become…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →