← Symbol Renault Symbol repair manuals →

Renault Symbol 1.4 16V K4J (2008): Engine Management System Diagnostics

The K4J 1.4 16V engine is controlled by an electronic control unit with multiport fuel injection. It determines engine load from intake manifold pressure. Diagnostics go from simple to complex: read the trouble codes, check power and grounds, evaluate live data, then check the ignition, fuel delivery, and engine mechanics.

DifficultyMedium Time1-2 hours Steps13

Parts

12
№Part
01 Spark plugsif faultyFind on Amazon →
02 Ignition coil moduleif faultyFind on Amazon →
03 Crankshaft position sensorif faultyFind on Amazon →
04 Camshaft position sensorif faultyFind on Amazon →
05 Manifold absolute pressure (MAP) sensorif faultyFind on Amazon →
06 Engine coolant temperature sensorif faultyFind on Amazon →
07 Oxygen sensor (upstream of catalytic converter)if faultyFind on Amazon →
08 Oxygen sensor (downstream of catalytic converter)if faultyFind on Amazon →
09 Knock sensorif faultyFind on Amazon →
10 Idle air control valveif faultyFind on Amazon →
11 Fuel filterif faultyFind on Amazon →
12 Fuel injectorsif faultyFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

13 steps
  1. Preliminary inspection. Check the engine oil and coolant levels, the condition of the battery (about 12.4-12.7 V with the engine off), and the battery terminals and ground cables. Inspect the vacuum hoses and intake ducts for cracks and air leaks, and check the sensor connectors for corrosion and damage.
  2. Connect the scan tool to the 16-pin OBD connector under the dashboard to the left of the driver. Turn the ignition on without starting the engine, then read and record all trouble codes along with the freeze-frame data. Only then clear the codes.
  3. Evaluate the type of codes. Permanent codes point to a persistent sensor or circuit fault. Intermittent codes are more often caused by poor contact, a corroded connector, or a broken wire. For misfire codes, check each cylinder individually, not just the general code.
  4. Check live data on a warmed-up engine (coolant temperature 85-95 °C). At idle: stable speed of about 750-850 rpm, intake manifold pressure within a reasonable range for idle, fuel trims without large deviations from zero, and the upstream oxygen sensor switching quickly. On a cold engine, the coolant temperature reading should match the ambient temperature.
  5. Check the coolant temperature sensor by comparing the scan tool reading with the actual temperature. A reading that is too high or too low causes a rich or lean mixture and hard starting.
  6. Check the manifold pressure sensor. With the ignition on and the engine off, the reading should be close to atmospheric pressure. At idle it should drop noticeably, and it should rise quickly when the throttle is opened sharply. Then check the sensor hose and the intake duct seal for leaks.
  7. Check the crankshaft and camshaft position sensors. If the engine cranks but does not start, look at the scan tool to see whether it shows engine speed while cranking. Measure the resistance of the inductive crankshaft sensor with a multimeter and compare it with the K4J specification. Check the sensor air gap to the flywheel or pulley and the condition of the wiring.
  8. Check the ignition. Remove the spark plugs and evaluate the deposit color: light brown is normal, black and dry means a rich mixture, white means a lean mixture, and oily means worn valve seals or piston rings. Installation torque is 20-30 N·m (15-22 lb-ft); confirm it against the markings on the spark plugs. Check the ignition coil module for breakdown and check for spark on each cylinder.
  9. Check fuel delivery. Connect a pressure gauge to the fuel rail. Pressure with the ignition on and at idle should be about 3 bar (acceptable range 2.5-3.5 bar), and it should not drop quickly after the ignition is turned off. Low pressure indicates a clogged filter, a weak pump, or a faulty regulator. Check injector operation by sound (with a stethoscope or a screwdriver) and by measuring coil resistance.
  10. Check the idle air control valve and the throttle body. A dirty throttle body and passage cause fluctuating idle speed and stalling. Clean with throttle body cleaner, taking care not to damage the throttle position sensor. After cleaning, an idle adaptation with the scan tool may be needed, or simply warm the engine up to operating temperature.
  11. Check the oxygen sensors. On a warmed-up engine, the upstream sensor should switch quickly (several times per second). A sluggish or constant signal indicates an aging sensor or an air leak. The downstream sensor should show a steadier signal. Also check the sensor heater by measuring its resistance.
  12. Check the engine mechanics if the electronics are normal. Measure compression on a warmed-up engine with the spark plugs removed and the fuel pump disconnected. The reference value for the K4J is about 12-14 bar, with no more than 1 bar difference between cylinders (for exact values, see the manufacturer's specifications). Also check the valve timing: the correct installation and tension of the timing belt.
  13. After fixing the cause, clear the codes, take a 10-15 minute test drive under various loads, and read the codes and live data again. Make sure the codes have not returned.

Common mistakes and warnings

  • Do not clear the codes before recording and analyzing them, or you will lose important information
  • Do not replace sensors at random: most faults are caused by wiring, connectors, air leaks, or grounds
  • Perform all work on the fuel system with the engine cold, away from open flame, and relieve the pressure carefully
  • If you lack the experience or the equipment to measure pressure and compression, take the car to a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →