← 9-3 Saab 9-3 repair manuals →

Saab 9-3 (YS3F) (2008): Diagnosing a Cruise Control That Won't Work

On the 9-3 II, cruise control cuts out or won't engage when the engine control module receives a wrong signal from the brake switch (and the clutch switch on manual transmissions). The most common cause is this switch or its wiring. This guide walks through the checks in order, from fault codes to the electrical circuits and controls. Saab service documentation lists codes P0573, P0703 and P1571 01 for this system. The sources give no exact resistance or voltage values, so the checks rely on whether the signal changes or not.

DifficultyMedium Time1-2 hours Steps24

Key figures

  • Speed range in which the system detects a brake switch fault
    3-40 km/h within 2-12 seconds. This is how the control module detects an open brake switch circuit (code P0573, step 6)
  • Steering column bracket cover fasteners
    3 screws. This is how many you need to remove to reach the column switch (step 17)
  • Column switch retaining clips
    2. You need to release them to pull the switch out (step 17)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: what the brake switch looks like and where its connector is

The brake switch seen from the side and above5Slot on the top face4Latch window1Switch body2Connector with pins3Plunger with a capThe plunger cap rests against the pedalTap to enlarge
  1. 1Switch body on the pedal bracket under the driver's dash: rectangular, with stiffening ribs. Check its position: it must act right at the start of pedal travel.
  2. 2Switch connector. Inspect it for corrosion, recessed pins and a loose crimp, and wiggle the connector and harness.
  3. 3Plunger with a round cap. If it is installed wrongly or sticks, the signal is unstable.
  4. 4Latch window in the body: a landmark when inspecting the switch.
  5. 5Slot on the top face of the body: a landmark when inspecting the switch.

Parts

6
№Part
01 Brake light switch (brake pedal switch), Saab 9-3 IImost commonFind on Amazon →
02 Clutch switch (manual transmission)less common, if faultyFind on Amazon →
03 Cruise control button moduleif faultyFind on Amazon →
04 Cruise control steering column switchif faultyFind on Amazon →
05 Steering wheel clock springif faultyFind on Amazon →
06 Ignition-on (+15) circuit fuseif faultyFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 7 more. See manuals →

Step by step

24 steps · 5 stages
Stage 1 of 5 Preparation and reading codes 5 steps
  1. Make sure the engagement conditions are met: the engine is running, the speed is above the cruise control minimum (usually 30-40 km/h), both pedals are released, and on an automatic the lever is in D.
  2. Check the brake lights: press the brake pedal and see whether both brake lights and the third brake light come on. If they don't come on, or they stay on all the time, the brake switch is at fault.
  3. Connect the scan tool and read the codes from the engine control module. For 2008 this is the EDC16 (diesel) or ME9/T8 (gasoline). Look for P0573 (brake switch circuit, open circuit), P0703 (brake pedal switch input circuit) and P1571 01 (incorrect brake light switch signal).
  4. Write down all the codes, then clear them and check whether they return. If there are no codes, go to step 5 and continue in order.
  5. If there are no codes, open the live data in the scan tool and find the "Brake Pedal Switch" and "Brake Light Switch" parameters. On a manual transmission, also check the clutch switch parameter if it is in the list.
Stage 2 of 5 Checking the brake switch 7 steps
  1. Press and release the brake pedal and watch the parameters in the scan tool. The status should change with every press. If the parameter doesn't change, the circuit is open or the switch is faulty. This is exactly the situation code P0573 describes: the car accelerates while the switch input stays "OFF".
  2. Find the switch on the pedal assembly bracket under the driver's side dash. If necessary, remove the lower trim panel under the steering column.
  3. Inspect the switch connector for corrosion, pushed-back pins and loose terminal crimps. Wiggle the connector and the wiring harness.
  4. Keep the operating principle in mind: on this car the brake switch is normally closed and opens when the pedal is pressed. The +15 supply reaches it through a fuse (the 2008 ME9 wiring diagram shows fuse 21), and the signal goes to the engine control module.
  5. Disconnect the connector and use a multimeter to check that the supply pin has voltage with the ignition on. If there is no voltage, check the fuse and the wiring from it.
  6. Check the switch for continuity: with the pedal released the contacts should be closed, and with the pedal pressed they should be open. If they aren't, replace the switch.
  7. Check the switch position: it should activate right at the start of pedal travel. If it is installed incorrectly or the plunger sticks, the signal will be unstable.
Stage 3 of 5 Checking the wiring and the clutch switch 4 steps
  1. Wiggle the harness leading from the switch in several places and directions while watching the multimeter, test light or the scan tool value. This will reveal an intermittent open or short.
  2. Check the signal wire from the switch to the engine control module for opens and for shorts to ground or power. Use the module pins from the wiring diagram for your specific engine.
  3. On a manual transmission car, check the clutch switch the same way: it also cancels cruise control when the pedal is pressed. An open circuit in it prevents the system from engaging.
  4. Check the engine control module and cruise control circuit fuses in the fuse boxes. Replace any blown fuses, but if a fuse has blown more than once, find the cause first.
Stage 4 of 5 Checking the controls 4 steps
  1. If the switches are good but the system won't engage, check the cruise control switch on the steering column. To get access, extend the steering wheel to its farthest position, remove the steering column bracket covers (3 screws) and carefully disconnect the switch (2 retaining clips), if your column version uses the same mounting.
  2. Inspect the switch connector, check the contacts for corrosion and wiggle the harness.
  3. If you suspect the steering wheel clock spring, check for other faults at the wheel: steering wheel buttons that don't work, or the airbag warning light being on. Work on the clock spring and airbag only with the battery disconnected, and wait at least 10 minutes first.
  4. If cruise control is operated by steering wheel buttons, check them with the scan tool: the value should change when you press a button.
Stage 5 of 5 Replacement and verification 4 steps
  1. Replace the faulty part: the brake switch (or clutch switch), the cruise control switch, or the damaged section of wiring. Tighten the switch on the pedal bracket to the manufacturer's specification and do not overtighten the fastener.
  2. Reconnect the connectors, check that the brake lights work, and clear the fault codes with the scan tool.
  3. Take a test drive on a level road: accelerate to 50-80 km/h, engage cruise control, then press the brake or clutch. The system should disengage and resume with the RES button.
  4. If the codes come back or the system still won't engage, check the throttle body (electronic actuator) and the engine control module. It is best to leave this stage to a repair shop with a Saab scan tool.

Common mistakes and warnings

  • The brake switch controls the brake lights and the stability control system, so after replacing it make sure the brake lights come on when you press the pedal and go off when you release it
  • Work near the steering wheel and clock spring involves the airbag: disconnect the battery, wait 10 minutes, and if you have no experience, take the car to a repair shop
Spotted a mistake? Tell us →