← Actyon Sports SsangYong Actyon Sports repair manuals →

Actyon Sports 2.0 e-XDi (2014): Serpentine (Drive) Belt Replacement

On the 2.0 e-XDi diesel, one long serpentine belt drives the alternator, power steering pump, A/C compressor and fan. The tensioner is automatic, so there is no separate tension adjustment. You need to move the tensioner arm aside, remove the old belt and route the new one correctly along the ribs.

DifficultyEasy Time30-60 minutes Steps11

Parts

3
№PartGenuine part no.Alternatives
01 Serpentine accessory drive belt (6 ribs, a little over 2 m long)Find on Amazon → 6719970192 AlternativesGatesContitechBosch
02 Accessory drive belt tensionerreplace at the same time on a high-mileage engineFind on Amazon →
03 Accessory drive belt idler pulleyreplace at the same time on a high-mileage engineFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

5
  • 14 mm wrench for the tensioner arm (check the size on your own tensioner) Amazon →
  • hex key or locking pin to hold the tensioner Amazon →
  • flashlight Amazon →
  • phone to photograph the belt routing Amazon →
  • socket set for removing the engine cover and air duct Amazon →
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

11 steps
  1. Shut off the engine and let it cool down. Open the hood and remove the plastic engine cover.
  2. For access to the belt, remove the air duct if it is in the way. If necessary, remove the engine undercover from below.
  3. Inspect the old belt. Cracks, oil stains and a frayed edge mean it is time to replace it. Oil on the belt may point to a leaking crankshaft seal, which must be fixed.
  4. Take a photo or draw a diagram of how the belt runs around the pulleys. The routing is not obvious, and a photo makes it easier to install the new belt later.
  5. Put the wrench on the automatic tensioner arm. Turn the arm in the direction that releases belt tension. Check the direction on the vehicle: the belt should go slack right away. Lock the arm with a hex key or pin if there is a locking hole.
  6. Slip the belt off the pulleys.
  7. Check the pulleys and rollers. The alternator should have no play, and the rollers should spin without noise, binding or play. If there is noise or play, replace the roller or the tensioner.
  8. Install the new belt. Start with the crankshaft, then route it onto the alternator, A/C compressor and power steering pump pulleys. Leave the tensioner and the idler pulley for the last. Each rib must seat in its own groove. Being off by even one rib will quickly wear out the edge of the belt.
  9. Slowly return the tensioner arm to its working position. The belt will tension itself.
  10. Check that the belt sits evenly on all pulleys. Reinstall the air duct, cover and undercover if you removed them. Take the tightening torques for the cover and undercover fasteners from the manufacturer's service manual. They are usually low.
  11. Start the engine and listen to it run. There should be no squealing or chirping. Check that the belt does not wander from side to side.

Common mistakes and warnings

  • Work only on a shut-off, cool engine and keep your hands away from the pulleys
  • Do not force the tensioner arm
  • It is spring-loaded and can snap back
  • The belt replacement interval is approximately 60,000-70,000 km
  • Check the exact figure in the manufacturer's service schedule
  • It is more convenient to replace the belt, rollers and tensioner as a set
Spotted a mistake? Tell us →