Autopapyrus · Subaru Impreza GD/GG (2003)
https://autopapyrus.com/catalog/subaru/impreza/guides/brake-fluid-replacement/
https://autopapyrus.com/catalog/subaru/impreza/guides/brake-fluid-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Subaru Impreza GD/GG (2003): Brake Fluid Replacement
The fluid is replaced by bleeding the brakes through the bleeder valves at all four wheels. The job takes two people: one smoothly presses the pedal, the other opens the valve. If the car has ABS, check the pedal stroke after the regular bleeding. If the stroke is more than specified, air may be left in the hydraulic unit.
Key figures
- Bleeder valve tightening torque8 N·m (71 lb-in), after bleeding each wheel (step 11); excessive force can strip the threads or break the valve
- Wheel orderfront right, rear left, front left, rear right, which purges the air correctly (step 6)
- Allowable pedal strokeno more than 90 mm without ABS, 95 mm with ABS, checked after bleeding (step 16)
- Final pedal holdabout 20 seconds, to check for leaks (step 15)
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part |
|---|---|
| 01 | DOT 3 or DOT 4 brake fluid (FMVSS No. 116)about 1 L (1.1 qt), fresh, from a single sealed container of one brandFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Chilton and 9 more.
See manuals →
Step by step
23 steps · 4 stagesStage 1 of 4 Preparation 5 steps
- Park the car on a level surface, apply the parking brake and shut off the engine. Loosen the wheel lug nuts.
- Lift the car and set it on solid jack stands. Remove all four wheels.
- Inspect the brake hoses, lines and fittings. There must be no leaks. If there is a leak, fix it before replacing the fluid.
- Clean the master cylinder reservoir cap and the area around it so that no dirt gets into the reservoir.
- Open the reservoir and remove the old fluid with a syringe or baster down to just above the bottom. Top up with fresh fluid to the MAX mark. Do not expose the bottom of the reservoir, or air will enter the system.
Stage 2 of 4 Bleeding the brake circuits 9 steps
- Bleed the brakes in this order: front right, rear left, front left, rear right.
- Remove the protective cap from the first wheel's bleeder valve. Fit the vinyl tubing onto the valve and put the other end into a container with a small amount of fresh fluid. Cover the valve with a rag so fluid does not spray onto nearby parts.
- Your helper presses the brake pedal smoothly and holds it down. The pedal must be pressed very slowly.
- Open the valve for 1-2 seconds to let the fluid and air out. Close the valve, and only then does your helper slowly release the pedal.
- Pause for 3-4 seconds between presses. Repeat steps 8-9 until clean, fresh fluid without bubbles comes through the tubing.
- When there are no more bubbles, close the valve and tighten it to 8 N·m (71 lb-in). This is a low torque, so do not overtighten, or you may strip the threads.
- Watch the fluid level in the reservoir and keep it full at all times. If it runs empty, air will enter the system and you will have to start over.
- Repeat steps 7-12 on the remaining wheels in the order given in step 6.
- Do not mix different brands of fluid, and do not use fluid from a container that has been open for a long time.
Stage 3 of 4 Checking 5 steps
- When all the wheels are bled, press the pedal all the way down and hold it for about 20 seconds. Check for leaks at the fittings and at the valves.
- Check the pedal stroke with the engine running at idle. Press the pedal with a force of about 490 N (roughly 50 kgf), and measure the distance from the pedal to the steering wheel. Measure the same distance with the pedal released. The difference must not exceed the specification: 90 mm for a car without ABS, 95 mm for a car with ABS.
- If the stroke is more than specified, air remains in the lines. Repeat the bleeding until the stroke is within specification.
- For a car with ABS: after regular bleeding, the hydraulic unit must be run in sequence control mode, which is done with a Subaru diagnostic scan tool. Then check the pedal stroke again. If it is still more than specified, air remains inside the hydraulic unit: repeat the bleeding and the sequence control run. If you do not have a scan tool, have a repair shop do this part; you can do the rest yourself.
- Top up the fluid to the MAX mark in the reservoir. Close the reservoir.
Stage 4 of 4 Finishing up 4 steps
- Wipe off the valves and calipers. Rinse any spilled fluid off with water and dry thoroughly: it damages the body paint.
- Fit the caps onto the valves, install the wheels and lower the car. Tighten the lug nuts in a crisscross pattern to the manufacturer's specified torque.
- Take a test drive at low speed and brake fairly firmly 2-3 times. Make sure all four wheels brake normally, with no sticking or pulling to one side. Check the reservoir level once more.
- If you disassembled the master cylinder or the reservoir ran empty, the master cylinder must be bled separately first. Disconnect the lines at the outlets, cover the cylinder with a bag, press and hold the pedal, plug the outlet with your finger and release the pedal. Repeat until the fluid comes out without air. Tighten the lines to 8 N·m (71 lb-in), then bleed the lines following steps 6-14.
Common mistakes and warnings
- Brakes are a safety matter
- If the pedal stays soft or "sinks" after repeated bleeding, do not drive the car and take it to a repair shop
- Brake fluid is toxic and damages paint
- Take used fluid to a recycling facility; do not pour it out
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →