← G01

SWM G01 (2025): Front Bumper Replacement

The G01 front bumper consists of a plastic cover held by screws at the top and bottom, push-pins in the wheel arches and snap-in clips at the edges. It is easier to remove with two people, so you don't damage the fenders or connectors. Check the exact torque values and fastener locations for your trim level in the manufacturer's service manual: the procedure below is based on the typical design of bumpers in this class.

DifficultyMedium Time1.5-3 hours Steps32

Parts

7
№Part
01 Front bumper assembly for SWM G01or bumper cover (paintable)Find on Amazon →
02 Bumper retaining clip and push-pin setFind on Amazon →
03 Front bumper reinforcement beamif neededFind on Amazon →
04 Front bumper lower air ductFind on Amazon →
05 Radiator grilleFind on Amazon →
06 Fog light bezelsFind on Amazon →
07 Tow hook coverFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

9

Step by step

32 steps · 7 stages
Stage 1 of 7 Preparation 4 steps
  1. Park the car on level ground, turn off the engine and set the parking brake. If you need access to the wheel arch fasteners and the underside of the bumper, raise the front of the car and securely support it on jack stands. Do not rely on a jack alone.
  2. Open the hood. Take photos of the old bumper from the front and side so you can compare the gaps with the fenders and hood later.
  3. Disconnect the negative battery terminal. This protects the electronics of the parking sensors and headlights.
  4. If the bumper has parking sensors, fog lights or a camera, prepare a container for the connectors and tape for labeling them in advance.
Stage 2 of 7 Removing the under-body shields and lower fasteners 5 steps
  1. Remove the lower engine splash shield (undertray) if it extends under the bumper. Remove the screws and push-pins and put them in a container.
  2. Remove the front wheels if the design of the wheel arch liners does not let you reach the bumper fasteners from below.
  3. Pull back or remove the front sections of the wheel arch liners: remove the screws and push-pins where they connect to the bumper.
  4. Remove the bumper retaining screws from underneath. On typical bumpers there are about four of these screws along the lower edge under the front section.
  5. Use a flat-blade screwdriver to pry out the push-pins that connect the bumper to the fender in the wheel arch. There are usually 2 on each side.
Stage 3 of 7 Access from the top 4 steps
  1. Remove the trim covers and the air duct above the radiator if they cover the upper row of bumper fasteners.
  2. Remove the 10 mm bolts along the top edge of the bumper and remove the plastic push-pins of the upper bracket.
  3. Check the upper side corners under the fenders: there is usually one screw on each side, sometimes two. Remove all that you find.
  4. If necessary, remove the radiator grille: it is often held by clips and screws, and it gets in the way when removing the bumper.
Stage 4 of 7 Disconnecting the wiring and removing the bumper 5 steps
  1. Disconnect the connectors for the fog lights, parking sensors, camera and washer reservoir hose (if the nozzles are mounted on the bumper). For each one, press the locking tab; do not pull on the wire. Label the connectors with tape.
  2. Ask your helper to support the bumper at one edge. Carefully pull the side corners toward you and slightly downward, releasing the clips on both sides. Be careful: the side clips are brittle and break under rough force.
  3. The top of the bumper is held by two clips. Press their front parts toward the car to release them.
  4. With your helper, remove the bumper by moving it forward and down. Place it cover-side up on a soft blanket.
  5. Inspect the bumper reinforcement beam, the absorber (foam filler), the brackets and the clips on the body. Replace any deformed parts.
Stage 5 of 7 Transferring parts to the new bumper 4 steps
  1. Remove the following from the old bumper and transfer them to the new one: grille, fog light bezels and bulbs, parking sensors, washer nozzles, tow hook cover, license plate brackets, moldings and stickers.
  2. Remove the license plate separately and install it on the new bumper after mounting.
  3. Replace broken push-pins and clips with new ones. Install plugs in the holes that are not used in your trim level.
  4. Place the new bumper next to the old one and compare the mounting points and cutouts. If the bumper is unpainted, paint it before installation.
Stage 6 of 7 Installation 6 steps
  1. With your helper, bring the bumper up to the body. Connect the fog light, sensor, camera and washer connectors before the bumper is fully seated.
  2. Guide the side corners into the guides at the fenders, then snap in the upper clips in the center.
  3. Install the upper row of bolts and screws. Tighten moderately: for the 10 mm bolts the approximate torque is 8-12 N·m (6-9 lb-ft); check the exact value in the manufacturer's service manual. Do not overtighten plastic.
  4. Install the lower screws and the push-pins in the wheel arches.
  5. Reinstall the wheel arch liners, radiator grille, air ducts and lower engine splash shield, then the wheels. Tighten the wheel bolts in a crisscross pattern to the G01 specification, usually in the range of 100-130 N·m (74-96 lb-ft); verify the value in the service manual.
  6. Reconnect the negative battery terminal.
Stage 7 of 7 Check 4 steps
  1. Check the gaps between the bumper, fenders, hood and headlights: they should be even and match the photos taken in step 2. If a corner sags, check the side clips and the upper screws.
  2. Turn on the ignition and check the parking lights, fog lights, parking sensors and camera, as well as the operation of the headlight washers or windshield washers if the nozzles are on the bumper. Make sure there are no error messages on the instrument panel.
  3. Start the engine, listen for unusual noises and make sure the bumper does not vibrate. Check the lower splash shield: it must not rub against the bumper.
  4. After the first 100-200 km (60-120 miles), inspect the bumper again and tighten any loose fasteners.

Common mistakes and warnings

  • Work only with the car supported on jack stands, and never get under it when it is supported by a jack alone
  • If the car has an adaptive cruise control radar, a camera or driver-assistance sensors, they may need to be calibrated at a repair shop after the bumper is replaced
  • The plastic clips at the edges of the bumper are brittle: do not use force and do not yank the bumper
  • If airbags or crash sensors are hidden in the bumper, do not damage the wiring or the connectors
Spotted a mistake? Tell us →