← T7

Tenet T7 (1st generation): Outer CV Joint Replacement (Front-Wheel Drive)

The outer CV joint is replaced when you hear clicking or crunching in turns under load, feel vibration at speed, or find a torn boot with grease leaking out. The job requires removing the axle nut, disconnecting the ball joint, and carefully seating the joint onto the shaft. The tightening torques in this text are approximate. Check the exact values against the manufacturer's specifications.

DifficultyHard Time2-4 hours per side Steps13

Key figures

  • Grease fill for a new CV joint
    about 2/3 of the joint's volume, with the rest spread inside the boot (step 9)
  • Service life of a new joint
    100,000-150,000 km, a rough guide for when to expect the next replacement; check the boot once a month

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

5
№Part
01 Front-wheel-drive outer CV joint assembly (joint, boot, clamps, grease, retaining ring)left or rightFind on Amazon →
02 Axle nut (hub nut)newFind on Amazon →
03 CV joint grease (shear-resistant, water-resistant, may be molybdenum-based)Find on Amazon →
04 Ball joint nutif neededFind on Amazon →
05 Tie rod end nutif neededFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

11

Step by step

13 steps
  1. Make sure the CV joint is really the cause: turn the steering wheel all the way to one side and pull away from a stop sharply. A clicking or crunching sound points to the CV joint on that side. Additional signs: grease splatter on the wheel rim and a torn boot.
  2. Park the car on a level surface, engage the parking brake, and place chocks behind the rear wheels. The wheels are still on the ground: remove the hubcap and loosen the axle nut with a long breaker bar (do not unscrew the nut yet).
  3. Loosen the wheel lug bolts, raise the front of the car with the jack, set a jack stand in place, and remove the wheel.
  4. Fully unscrew the axle nut. It is best to replace it with a new one, and the tightening below should be done to the manufacturer's specification.
  5. Disconnect the lower ball joint from the steering knuckle and, if necessary, the tie rod end (using a ball joint separator). The brake caliper with the rotor does not always need to be removed, only if it blocks access. If you remove it, hang the caliper on a wire; the hose must not hang loose.
  6. Use a pry bar to move the hub away from the lower control arm and pull the outer joint out of the hub. If the splines are stuck, tap the end of the shaft with a hammer through a wooden block. Do not strike the shaft with bare metal.
  7. Remove the clamps from the old boot (you can cut them) and slide the boot along the shaft. The CV joint is held on by a retaining ring: knock the joint off the shaft with sharp, controlled hammer blows. If the ring is jammed, free it with needle-nose pliers or a screwdriver. In difficult cases, remove the entire axle and cut the joint off.
  8. Wipe off the splines and the shaft, and check them for wear and galling. The shaft must be clean and dry. Compare the new CV joint with the old one: the number of splines, diameter, length, and the ABS sensor ring (tone ring) must match.
  9. Fill the new CV joint with grease to about 2/3 of its volume and spread the rest inside the boot. Do not use all-purpose lithium or graphite grease.
  10. Slide the new boot onto the shaft, then press the CV joint onto the shaft all the way, until the retaining ring clicks into place. Pull the boot over the joint housing and secure it with the clamps. Tug the joint by hand: it must not come off.
  11. Insert the axle into the hub, aligning the splines, reconnect the ball joint and tie rod end, and if needed reinstall the caliper and rotor. Tighten the ball joint, tie rod end, and caliper with a torque wrench to the manufacturer's specification.
  12. Thread on the new axle nut, install the wheel, lower the car to the ground, and tighten the axle nut with a torque wrench to the specification (incorrect tightening quickly ruins the wheel bearing). Tighten the wheel lug bolts in a crisscross pattern to the specified value.
  13. Take a test drive at low speed with turns: there should be no clicking or vibration. After the replacement, check the wheel alignment and adjust it if necessary.

Common mistakes and warnings

  • This job involves the steering and suspension, and incorrect tightening of the axle nut and ball joint is dangerous
  • If you lack experience and a torque wrench, leave the replacement to a repair shop
  • Do not drive with a torn boot: dirt quickly destroys the CV joint and can damage the hub
  • The right and left axles are different, so match the part to the correct side
  • Inspect the boots about once a month and after driving through mud or road salt, and avoid hard launches with the steering wheel turned
Spotted a mistake? Tell us →