← Patriot

UAZ Patriot (2012): Fuse and Relay Box Diagram

The 2012 Patriot has three main units: a mounting block in the cabin, a block under the hood and, depending on trim level, separate blocks for the air conditioner and glow plugs. The cabin block for this year is type 2 (produced 2012-2014). Numbering and circuit assignments vary by year and trim level, so compare the table below with the diagram on the block cover.

DifficultyEasy Time15-30 minutesinspection and testing Steps18

Key figures

  • Rear window and mirror heating fuseF14 in the cabin block, step 7
    20 A
  • Cigarette lighter and seat heating fuseF12, step 8
    20 A
  • Heater fuseF18, step 8
    25 A
  • Left headlight low beam fuseF4, step 6
    7.5 A
  • Left headlight high beam fuseF6, step 6
    10 A
  • High-current links at the battery on automatic versionsstep 5, disconnect the negative terminal before working
    2 x 100 A

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

8
№PartAlternatives
01 Blade fuse (standard) 5 AFind on Amazon → AlternativesBoschEra
02 Blade fuse (standard) 7.5 AFind on Amazon → AlternativesBoschEra
03 Blade fuse (standard) 10 AFind on Amazon → AlternativesBoschEra
04 Blade fuse (standard) 15 AFind on Amazon → AlternativesBoschEra
05 Blade fuse (standard) 20 AFind on Amazon → AlternativesBoschEra
06 Blade fuse (standard) 25 AFind on Amazon → AlternativesBoschEra
07 Blade fuse (standard) 30 AFind on Amazon → AlternativesBoschEra
08 Automotive relay 12 VFind on Amazon → AlternativesBoschEra

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

4

Step by step

18 steps · 5 stages
Stage 1 of 5 Block locations 5 steps
  1. The cabin block is under the instrument panel on the driver's side, behind a protective cover. Remove the cover; it opens without tools.
  2. The engine compartment block is under the hood on the left, next to the battery, under a protective cover.
  3. The air conditioner block (relays and fuses) is under the hood on the right.
  4. On Iveco diesel versions, the glow plug relays and the main glow plug fuse are on the left, near the firewall of the engine compartment.
  5. On some automatic transmission vehicles, an additional block with two 100 A fusible links is installed on the positive battery terminal. They protect the mounting blocks.
Stage 2 of 5 Cabin block, type 2 (2012-2014), fuses 3 steps
  1. Lighting: F1 — 5 A, left parking light. F2 — 5 A, right parking light. F3 — 7.5 A, right low beam. F4 — 7.5 A, left low beam. F5 — 10 A, right high beam. F6 — 10 A, left high beam. F7 — 7.5 A, fog lights. F16 — 10 A, right fog light. F17 — 10 A, left fog light. F19 — 7.5 A, brake light switch and cabin dome lights.
  2. Body electrical: F8 — 20 A, door locks. F9 — 10 A, hazard warning lights. F11 — 30 A, power windows. F13 — 20 A, horn. F14 — 20 A, rear window and exterior mirror heating, light control module. F15 — 20 A, windshield wiper, its switch, rear heater switch. F20 — 5 A, mirror controls.
  3. Other circuits: F10 — 10 A, transmission connector, reverse light switch, speed sensor, central lamps, hazard switch. F12 — 20 A, cigarette lighter and seat heating. F18 — 25 A, heater. F21 — 10 A, air conditioner compressor. F22 — 15 A, power outlets.
Stage 3 of 5 Cabin block, relays 1 step
  1. K1 and K2 — fog lights. K3 — high beam. K4 — low beam. K5 — load-shedding relay. K6 — auxiliary heater (for ZMZ 40904 and 40905 engines). K7 — air conditioner compressor. K8 — turn signal and hazard flasher relay. K9 — intermittent wiper relay.
Stage 4 of 5 Engine compartment block 3 steps
  1. Fuses (the source gives only circuit assignments, without ratings): F1 — horn. F3 — second electric cooling fan. F4, F10, F18 — ABS (ESP). F5 — instrument cluster. F6 — fuel pump. F7 — starter. F8 — electric cooling fan. F9 — engine management system. F11, F12, F13 — pre-start heater. F17 — 60/90 A high-current fuse, mounting block and windshield heating. F19 — mounting block. F2, F14, F15, F16 are not installed.
  2. Relays: R1-R10 are double positions that hold the relays for the starter, cooling fan(s), fuel pump, engine management system, horn, heater, air conditioner compressor and recirculation flap. The exact assignment of the sockets depends on the block type (old or new), so check the diagram on the cover.
  3. Air conditioner and glow plug block (Iveco diesel): F1 — 7.5 A compressor clutch; F2 and F3 — 30 A each, fans; F4 — 60 A, glow plug power supply. Relays: K1 — heater fan switch-on, K2 and K3 — recirculation flap, K4 — compressor clutch, K5 and K6 — fans, K7 — glow plugs.
Stage 5 of 5 Replacing a fuse and testing a relay 6 steps
  1. Shut off the engine, turn off the ignition and the affected accessory, and find the needed circuit in the table.
  2. Pull the fuse out with the fuse puller and hold it up to the light: a broken element means it has blown.
  3. Install a new fuse with the same rating. Never use a makeshift bypass (wire or "bug") or a fuse with a higher rating: the wiring will overheat.
  4. If the new fuse blows right away, look for a short circuit or a faulty component; do not increase the rating.
  5. Test a relay by swapping it with a known good relay of the same function (for example, K3 and K4 in the cabin block) or with a multimeter: coil resistance is usually tens of ohms, and the contacts should close when 12 V is applied.
  6. Snap the block covers back into place so moisture and dirt do not get inside.

Common mistakes and warnings

  • Before working on the high-current fuses (60/90 A, 100 A) and the links at the battery, disconnect the negative terminal
  • Torque specs are not needed, since there are no fasteners
  • Fuse numbering and circuit assignments vary by year and trim level, so if the diagram on the block cover differs from the table above, follow the cover
  • For severe cases (repeated blowing, melted sockets), take the vehicle to a repair shop
Spotted a mistake? Tell us →