Autopapyrus · Volvo FH (2nd generation)
https://autopapyrus.com/catalog/volvo/fh/guides/checking-and-adjusting-front-wheel-toe/
https://autopapyrus.com/catalog/volvo/fh/guides/checking-and-adjusting-front-wheel-toe/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Volvo FH (2nd generation): Checking and Adjusting Front Wheel Toe
Toe on the Volvo FH is adjusted by changing the length of the tie rods. The procedure requires a 3D wheel alignment system to accurately measure the wheel alignment angles. The recommended check interval is every 15,000-20,000 km, or after replacing suspension or steering components.
Parts
2| № | Part | Alternatives |
|---|---|---|
| 01 | Tie rod assemblies with endsif wornFind on Amazon → | AlternativesLemförderTRWFebi Bilstein |
| 02 | Lock nutsif wornFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Step by step
12 steps- Position the vehicle on the alignment rack. Make sure the tire pressure is correct (usually 8-9 bar on the front axle) and that the cargo area is empty or matches the normal operating load.
- Attach the measuring heads to the wheels and calibrate the system according to the equipment manufacturer's instructions.
- Roll the vehicle forward and back to compensate for suspension play, then set the wheels to the straight-ahead position.
- Measure the current toe, camber and caster angles. Record the results.
- Compare the measured values with the specifications for the Volvo FH (typical front axle toe range: 0-2 mm per side, 0-4 mm total; exact values depend on the front suspension type and model year, so check the manufacturer's specifications or the alignment system database).
- If toe is out of tolerance, proceed with the adjustment. Apply penetrating oil to the threaded connections of the tie rods and let it soak in for 10-15 minutes.
- Loosen the lock nuts on both tie rods (the left and right are adjusted in sync to keep the steering wheel centered).
- Turn the tie rod adjusting sleeve: shortening the rod reduces toe-in (the wheel turns outward), and lengthening it increases toe-in (the wheel turns inward). Adjust each side in turn in small increments (1-2 turns), checking the readings on the alignment system.
- Once the required toe is reached, tighten the lock nuts to 200-300 N·m (148-221 lb-ft). The exact value depends on the tie rod type, so check the technical documentation. Hold the adjusting sleeve with a second wrench to keep it from turning.
- Perform a final measurement on the alignment system. Make sure the angles are within tolerance and the steering wheel is straight when driving in a straight line.
- Check the tightening torque of the tie rod end ball stud nuts (typical torque 150-200 N·m (111-148 lb-ft)) and install cotter pins if the design calls for them.
- Print the alignment report and keep it for the maintenance history.
Common mistakes and warnings
- Adjusting toe on a truck without a 3D alignment system (by eye or with a tape measure) is not acceptable
- An error of 1-2 mm leads to accelerated tire wear (a set of tires for the FH is expensive) and poorer handling at speed
- If you find play in the ball joints of the tie rod ends or in the tie rods, adjustment is pointless
- The worn parts must be replaced, and the alignment angles must then be set again
- After the adjustment, always take a test drive and check that the vehicle does not pull to one side
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Volvo Brand
Volvo Car Corporation (originally Volvo Personvagnar AB) is a Swedish passenger car maker. The name "Volvo" is Latin…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →