← XC90 Volvo XC90 repair manuals →

Volvo XC90 II (2020): 12 V Battery Replacement

On the XC90 II the battery is not under the hood. It is in the cargo area, under the floor. Access is easy, but you must install a replacement with exactly the same type, dimensions and cold cranking amps. After the battery is disconnected, the power tailgate and power windows need to be reset, and the new battery should be registered in the charge management system. This guide covers the 12 V starter battery only. Do not touch the additional 48 V battery on mild hybrids or the traction battery on plug-in hybrids: that work is for an authorized service center.

DifficultyMedium Time40-60 minutes Steps27

Key figures

  • Battery mounting bolt socket size
    8 mm. Use an 8 mm socket with a ratchet in steps 11 and 13 to remove the bolts that hold the battery.

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

2
№Part
01 12 V starter battery, AGMsame type, dimensions and cold cranking amps as the installed oneFind on Amazon →
02 Memory saver kit (external 12 V power source)optionalFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more. See manuals →

Step by step

27 steps · 5 stages
Stage 1 of 5 Preparation 5 steps
  1. Park the vehicle on a level surface, turn off the engine, close all doors, and remove the key or take the key fob out of the cabin. Wait a few minutes.
  2. Write down any settings that may be reset: radio stations, clock, seat positions. Find the radio code if one is required.
  3. Open the doors and lower the windows 2-3 cm so you don't get locked out after the battery is disconnected and so the window auto function is easier to reset later.
  4. Open the tailgate. Remove jewelry and rings so you don't short the terminals.
  5. If you have an external 12 V power source, connect it to the factory jump-start points under the hood in the far right corner to preserve the control modules' memory.
Stage 2 of 5 Accessing the battery 3 steps
  1. Lift the cargo area carpet. Unclip the two straps that hold the floor to the body and remove the entire cargo floor.
  2. Take out the organizers and storage boxes if they are in the way. The battery will be visible under a plastic cover.
  3. Remove the plastic cover: it is not held by screws, it simply lifts straight up. Note how the vent hose and wires are routed.
Stage 3 of 5 Removal 7 steps
  1. Loosen the clamp on the negative cable with a wrench and move it aside so it cannot touch the terminal. The negative is always removed first.
  2. Open the protective cap on the positive terminal and loosen the clamp. Move the cable aside.
  3. Remove the two bolts on the sides of the battery and the one bolt at the front, at the bottom of the battery, with an 8 mm socket.
  4. Remove the metal hold-down cover that presses on the battery.
  5. Remove one more bolt at the bottom right: it holds the metal plate that secures the battery. Remove the plate.
  6. Lift the battery out by its case, keeping it strictly upright. It is heavy, so lift with both hands and do not press it against your clothing. Do not tilt it.
  7. If the old battery has a vent hose, remove it and transfer it to the new battery in the same position.
Stage 4 of 5 Installation 6 steps
  1. Wipe the tray and brackets with a dry rag and remove dirt and any traces of electrolyte. Clean the cable terminals with a brush.
  2. Compare the new battery with the old one: type, dimensions, positive and negative terminal positions, cold cranking amps.
  3. Set the new battery in the tray the same way the old one sat, and connect the vent hose if there was one.
  4. Install the plate and the metal hold-down cover, and tighten all the mounting bolts (6 retaining bolts). The torque values are approximate; check the exact figures against the manufacturer's specification. The bolts for the box and battery hold-down are usually tightened in the range of 8-13 N·m (6-10 lb-ft). The battery must not move.
  5. Connect the positive terminal first, then the negative. The approximate clamp tightening torque is 5-7 N·m (4-5 lb-ft), no more: the terminal post is easy to damage. Close the positive cap.
  6. Install the plastic cover and the cargo floor, and clip the straps back in place.
Stage 5 of 5 Reset and check 6 steps
  1. Turn the ignition on and wait for the modules to boot. Error messages may appear; they often disappear after starting the engine and driving.
  2. Reset the window auto function: lower each window fully and hold the button for 1-2 seconds, then raise it fully and hold the button for 1-2 seconds. If the power tailgate needs a reset, do it following the instructions in the vehicle menu.
  3. Enter the radio code if required. Set the clock and stations.
  4. Start the engine and check that there are no fault messages in the instrument cluster. The transmission may re-learn your driving style, so shifts may feel different during the first few kilometers.
  5. Register the new battery in the charge management system (using a diagnostic service function, which is done at a repair shop with diagnostic equipment). Without this, the alternator may charge the new battery using the old battery's settings.
  6. Take the old battery to a recycling point: do not throw it away.

Common mistakes and warnings

  • Always disconnect the negative first, and when installing, connect the positive first
  • Otherwise you can short the circuit, even to the point of causing a fire
  • The battery gives off explosive gas: do not smoke or work near open flames
  • If you are not confident working on the vehicle's electrical system, or if you need the battery registration done, contact a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →