← Fiat

Fiat Doblo no longer responds to the accelerator pedal

Fiat Doblo · 2013 11 answers Translated from Russian · original

A Fiat Doblo 223 Cargo, 2013, 1.4, has come in for repair. It doesn't respond to the accelerator pedal. It starts normally and holds a little over 1000 rpm. When I press the pedal, revs rise slightly to 1300-1400 and no further, with no other reaction. The active fault codes are P1121 and P1122 - Throttle valve posit. Track 1 and 2. The throttle body won't adapt (learn). A replacement throttle body gave the same result. I checked the wiring from the throttle body to the ECU and it's all fine and in the right places, and the connectors are clean. I checked the 5 V reference voltage and it is MISSING. That is the problem. ECU: IAW-5SF MH 228. 1) Can you work out what controls and monitors the throttle in the ECU, and can it be repaired? 2) If I replace the ECU with a used one, how do I properly pair it to the immobilizer? 3) Can a donor ECU be made to look like a new one? I have the key card code. 4) What is the right tool to read and write the dump?

Answers
O
Owner Feb 06, 2021

If you power the ECU on the bench, is the 5 volts missing there too?

O
Owner Feb 14, 2021

I haven't tried that. On the car I checked the grounds and the constant positive from the battery and from the ignition switch, and there is 12.2 V. I checked the reference on the MAP sensor and it has 5 V, which is normal. I pulled the positive pin out of the ECU connector and powered it from the MAP sensor's supply instead. The result was zero, and the throttle body doesn't work.

O
Owner Feb 19, 2021

Is the pedal's supply all right? Usually, when the 5 V drops out, an external supply helps. But it's better to fit a 7805 in the right circuit than to take power from other sensors.

O
Owner Mar 14, 2021

Is the pedal's supply all right? Usually, when the 5 V drops out, an external supply helps. But it's better to fit a 7805 in the right circuit than to take power from other sensors.

O
Owner Apr 03, 2021

Yes, the pedal is fine. What is a 7805? I took the supply from the MAP sensor just to test. My guess is that not only has the 5 V dropped out, but the part that processes the signals from the potentiometers isn't working either. That's why I asked which component in the ECU controls these signals.

O
Owner May 22, 2021

The L7805 is a voltage regulator. The question above was a fair one: is this voltage missing on the bench too? Maybe some circuit is pulling it down.

O
Owner Jun 03, 2021

I haven't tried it on the bench. The engine runs normally otherwise. What circuit could it be, if all the other parameters are normal?

O
Owner Aug 26, 2021

Then apply an external 5 V and see.

O
Owner Sep 29, 2021

I applied 5 V from the MAP sensor and got the same 5 V, but I had pulled the throttle's positive pin out of the ECU connector.

O
Owner Oct 22, 2021

If the 5 V doesn't sag in that case, then test the throttle drive driver in the ECU and replace it.

Autopapyrus assistant AI assistant Sep 20, 2026

Since the external supply didn't bring the throttle body back to life, it means that more than the 5 V line has failed in the ECU. The whole throttle control channel (the driver plus the potentiometer signal processing) is out. Repairing the IAW board is possible, but it needs a schematic and micro-soldering experience, so look for an automotive ECU electronics specialist. For a used replacement, the immobilizer has to be adapted with a programmer (for example FGTech or similar). You write the donor ECU's dump, then enter your car's immobilizer PIN code and crypto key into it. You can make the donor look new virtually (reset the mileage and VIN in the dump), but physically it will still be a used unit. To read and write the IAW-5SF, Kess, K-TAG or Byteshooter via the BDM port will work.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →