Autopapyrus · Audi A3 (8L)
https://autopapyrus.com/catalog/audi/a3/guides/engine-air-filter-replacement/
https://autopapyrus.com/catalog/audi/a3/guides/engine-air-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Audi A3 (8L): Engine Air Filter Replacement
On the A3 8L with the AEH engine, the air filter sits in a plastic housing in the engine bay. To replace it, you open the housing cover, take out the old element and install the new one. The job takes about 10 minutes and needs no special tools. The usual replacement interval is 30,000-60,000 km or once a year, and you should change it more often if you drive on dusty roads.
Key figures
- Work timethis is how long the replacement usually takes, so there is no need to rush or remove anything extra (steps 3-8)about 7-10 minutes
- Number of cover fastenersthis is how many screws or clips to release to lift the cover (step 3)2-4, depending on the housing version
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | Panel-type engine air filter for Audi A3 8L 1.6 (AEH)Find on Amazon → | 1J0129607S | AlternativesMannBoschFiltronKnecht/Mahle |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
2
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 10 more.
See manuals →
Step by step
9 steps- Shut off the engine, let it cool down and open the hood. If you like, cover the fender with a protective cover so you don't scratch the paint with the screwdriver.
- Find the black plastic air filter housing. It is connected to the throttle body by a duct.
- Use a Phillips screwdriver to remove the screws (fasteners) that hold the housing cover. There are only a few, usually 2-4, depending on the housing version. If the housing has clips instead of screws, release them.
- Carefully lift the housing cover. It is best not to disconnect the connectors and hoses that run to it. If a hose gets in the way, note how it is routed and then remove it.
- Note how the old filter is sitting, then take it out.
- Inspect the inside of the housing. Remove dust, leaves and debris with a dry or slightly damp rag. Make sure no dirt falls into the duct leading to the engine.
- Install the new filter so that its sealing edge seats firmly in the housing all the way around, with no misalignment or gaps.
- Put the cover back in place and check that it sits flat and does not pinch the filter. Then tighten the screws or snap the clips shut. Tighten the screws moderately, without much force: the housing is plastic, and there is no specified torque for these screws.
- Check that all ducts and connectors are in place. Start the engine, make sure it runs smoothly and close the hood.
Common mistakes and warnings
- Work only with the engine off
- Never drive without the filter or with a misaligned cover: unfiltered air gets into the cylinders and speeds up engine wear
- If the filter is very dirty or soaked with oil, check the crankcase ventilation system instead of just replacing the filter
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Audi
Audi AG is a German company and part of the Volkswagen Group, best known for building Audi cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →