Autopapyrus · Haval F7 (2026)
https://autopapyrus.com/catalog/haval/f7/guides/engine-air-filter-replacement/
https://autopapyrus.com/catalog/haval/f7/guides/engine-air-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Haval F7 (2026): Engine Air Filter Replacement
Model year 2026 vehicles are second-generation F7s. The engine air filter sits in a conveniently located housing, and the cover is held by five Phillips screws. The screws are captive, so they can't be lost. The replacement takes only a few minutes.
Key figures
- New filter sizeapprox. 255×165 mm. Compare it with the old one when buying: vehicles built before 2024 use a different filter size.
- Screws on the cover5 pcs. Remove them with a Phillips screwdriver; the screws are captive and do not come out of the cover, so there is no need to pull them out.
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the filter is and how to open the housing
Tap to enlarge
- 1housing lid: lift it to reach the filter
- 2lid screws, 5 pcs: undo with a Phillips screwdriver, they stay in the lid
- 3the filter itself: this is what you replace; the rubber edge must sit flat, not twisted
- 4lower part of the housing: stays in place, just wipe out the dust
- 5big hose to the engine: leave it alone, do not disconnect it
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | Engine air filter, panel type, approx. 255×165 mmFind on Amazon → | AlternativesNordfilSakuraGoodwill |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
2Step by step
10 steps- Shut off the engine, let the engine bay cool down, and open the hood.
- Locate the air filter housing. It is in an easily accessible spot in the engine bay.
- Use a Phillips screwdriver to remove the five screws on the housing cover. The screws stay in the cover.
- Lift the cover and move it aside, without stretching or damaging the hoses and wiring attached to it.
- Remove the old filter element and check its condition. If it is heavily clogged with dust and sand, replace it right away.
- Wipe the inside of the housing and the seal seating surface with a dry rag. Do not let any debris get into the intake tract.
- Install the new element flat, without tilting, so the seal sits tightly around the entire perimeter.
- Put the cover back and tighten all five screws. The housing is plastic with no metal inserts: tighten smoothly, without force, until snug, and do not strip the threads. The torque for these screws is low; for the exact value, follow the manufacturer's specification.
- Check that the cover sits flush with no gaps and that the hoses and connectors are in place.
- Start the engine, check that it idles smoothly, and listen for any unusual air-leak noises from the intake.
Common mistakes and warnings
- Do not overtighten the cover screws: plastic threads strip easily
- The replacement interval depends on operating conditions; on dusty roads and in sandy areas, check the filter more often
- Many owners replace it earlier than the interval in the service book, for example every 15,000 km
Spotted a mistake? Tell us →
Our articles
Before you buy
German Turbo Engines vs. Chinese Ones: Which Lasts Longer? An Honest Look at Engine Life
Volkswagen 1.4 and 2.0 TSI, BMW N20 and Mercedes M274 versus Haval, Chery and Geely engines: lifespan benchmarks…
Read →
Brand stories
The History of Great Wall Motors
Great Wall Motors Ltd. has been one of China's largest automakers since 1995. It is essentially a holding company that…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →