Autopapyrus · Haval F7 1.5 Turbo GW4B15A 150 hp (2025)
https://autopapyrus.com/catalog/haval/f7/guides/engine-oil-and-oil-filter-replacement/
https://autopapyrus.com/catalog/haval/f7/guides/engine-oil-and-oil-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Haval F7 1.5 Turbo GW4B15A 150 hp (2025): Engine Oil and Oil Filter Change
Change the oil and filter on the 1.5T with the engine warm. Owners commonly change it every 7-8 thousand km (4,300-5,000 miles), but check your service book for the exact official interval. 2025 model-year cars are the second-generation F7, and your trim has the 1.5T engine. The procedure is standard: drain from below, replace the filter, and refill through the filler neck under the decorative cover.
Key figures
- Oil fill volumeabout 4 L (4.2 qt). This is how much to buy and pour in after changing the filter (steps 16-17). Check with the dipstick and do not overfill
- Oil viscosity0W-20. This suits this engine. Do not choose a different viscosity without a need
- Change intervalevery 7-8 thousand km (4,300-5,000 miles). This is common practice for this engine to avoid wearing out the turbo engine. Check your service book for the exact official interval
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the drain plug and oil filter cap are
Tap to enlarge
- 1Drain plug on the oil pan side wall: unscrew with a 14 mm socket, the first jet shoots sideways, let the oil drain, fit a new washer
- 2Filter cap with a hex: unscrew slowly with a 27 mm socket until the oil drains, tighten with a torque wrench
- 3Oil filter housing: cast bracket around the cap, underneath, put a drain pan under it
- 4Oil pan: aluminum, do not overtighten the plug so as not to strip the thread
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | 0W-20 engine oilabout 4 L (4.2 qt); 4-5 L (4.2-5.3 qt) containerFind on Amazon → | |
| 02 | Oil filter for Great Wall 1.5T engines (replacement cartridge with sealing rings)for a filter in a housing with a cap; for a spin-on housing, a spin-on filterFind on Amazon → | AlternativesMannMahleHengst |
| 03 | Drain plug sealing washer (aluminum or copper)newFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8Step by step
23 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Warm up the engine for 5-10 minutes to operating temperature so the oil thins out and drains completely. Shut off the engine and wait 5 minutes.
- Park the car on level ground, on a lift, or over a pit. Apply the parking brake. If you use jack stands, place them only at the factory support points.
- Open the hood and remove the decorative engine cover to reach the oil filler neck. Unscrew the filler cap and set it aside in a clean place, which speeds up draining.
- Get the new oil, filter, sealing washer, and tools ready. Wipe the area around the drain plug and the filter housing.
Stage 2 of 5 Draining the oil 4 steps
- If an engine skid plate is installed underneath, remove it (fasteners and the number of bolts depend on the trim, so have a socket set on hand).
- Place the drain pan under the oil pan drain plug. Keep in mind that the first stream shoots out to the side.
- Remove the drain plug with a 14 mm socket (check the size against the head on your plug). Let the oil drain completely, 10-15 minutes.
- Inspect the plug and the threads. Replace the sealing washer with a new one. Wipe the seating surface.
Stage 3 of 5 Replacing the filter 5 steps
- Place the pan under the oil filter housing (it is located underneath and is accessible without removing the engine). Lay rags around it.
- If the filter is a cartridge under a plastic cap, unscrew the cap with a 27 mm socket. Unscrew it slowly until the oil drains out of the housing, otherwise you will end up covered in oil. If the filter is a spin-on type, remove it with a filter wrench or by hand.
- Remove the old cartridge together with the cap, and take the old sealing rings off the cap if the kit comes with new ones.
- Wipe the housing and the cap with a clean rag. Lubricate the new rings with fresh oil and install them on the cap and the cartridge. Insert the new cartridge all the way in.
- Thread the filter cap on by hand until it contacts, then tighten it with a torque wrench. The approximate torque is no more than 25 N·m (18 lb-ft) (plastic cap, do not overtighten; verify the exact value against the manufacturer's specification). For a spin-on filter: lubricate the gasket with oil and tighten by hand, then add 3/4 of a turn. Do not use a tool to tighten it.
Stage 4 of 5 Tightening the plug and refilling 5 steps
- Install the drain plug with a new washer. Tighten it with a torque wrench to 25-35 N·m (18-26 lb-ft) (the range is approximate, verify the exact value against the manufacturer's specification). Do not overtighten: an aluminum oil pan strips easily.
- Reinstall the engine skid plate, if you removed it.
- Lower the car. Pour in about 3.5 L (3.7 qt) of 0W-20 oil through the funnel, then wait a couple of minutes for the oil to drain down into the oil pan.
- Check the level with the dipstick: add oil in small amounts up to the mark between MIN and MAX. The total fill capacity is about 4 L (4.2 qt) (with the filter). Do not overfill.
- Close the oil filler cap and install the decorative cover.
Stage 5 of 5 Checking 5 steps
- Start the engine and let it run for 30-60 seconds. The oil pressure light should go out 1-2 seconds after startup. If it does not, shut off the engine immediately and look for the cause.
- Inspect the drain plug and the filter cap for leaks. Wipe them lightly and make sure nothing is seeping.
- Shut off the engine, wait 5 minutes, and check the level with the dipstick again. Top up to the proper level if needed.
- Reset the service interval in the instrument cluster following the instructions for your trim (through the onboard computer menu).
- Pour the used oil into a container and take it to a collection point. Do not pour it down the drain or onto the ground.
Common mistakes and warnings
- Work on an engine that is warm but not hot: the oil and the exhaust manifold can cause burns
- A car on jack stands that are not placed at the factory support points is dangerous
- If you have no experience working under a car, leave the job to a repair shop
- Do not use oil of a different viscosity
- Stick to 0W-20 (for a turbocharged direct-injection engine, it is important to meet the manufacturer's approval specification)
Spotted a mistake? Tell us →
Our articles
Before you buy
German Turbo Engines vs. Chinese Ones: Which Lasts Longer? An Honest Look at Engine Life
Volkswagen 1.4 and 2.0 TSI, BMW N20 and Mercedes M274 versus Haval, Chery and Geely engines: lifespan benchmarks…
Read →
Brand stories
The History of Great Wall Motors
Great Wall Motors Ltd. has been one of China's largest automakers since 1995. It is essentially a holding company that…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →