Autopapyrus · Iveco Daily 2.3 F1A (2006)
https://autopapyrus.com/catalog/iveco/daily/guides/engine-oil-and-oil-filter-replacement/
https://autopapyrus.com/catalog/iveco/daily/guides/engine-oil-and-oil-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Iveco Daily 2.3 F1A (2006): Engine Oil and Oil Filter Replacement
The F1A lubrication system is serviced by changing the oil and oil filter. The total fill capacity for the 2.3 F1A is about 5.5-5.7 L (5.8-6.0 qt), depending on the engine version. The oil in the pan sits between marks of roughly 3 L (3.2 qt) (minimum) and 4.3 L (4.5 qt) (maximum). Some oil stays in the filter and the oil cooler, so checking the level on the dipstick after the change is mandatory.
Key figures
- Engine oil capacityabout 5.5-5.7 L (5.8-6.0 qt). This is what you need to add when changing the oil and filter, while the pan holds 3-4.3 L (3.2-4.5 qt) between the dipstick marks (steps 10-12)
- Suitable oil viscosity5W-30 or 15W-40. Choose when buying the oil (part)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: what the oil filter looks like and what to check when replacing it
Tap to enlarge
- 1Oil filter: unscrew the old one, lubricate the ring of the new one with clean oil and fit it
- 2Filter sealing ring: rubber, in the groove at the edge of the end face; wipe the seating surface and lubricate the ring with oil
- 3Oil holes in the filter support plate
- 4Threaded neck in the center: the filter screws onto the engine by it
- 5Marking on the body (OP 592/9): check the filter for the F1A 2.3 against it when buying
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Engine oil for diesel engines (Iveco/ACEA)Find on Amazon → | |
| 02 | Oil filter for F1A 2.3 engineFind on Amazon → | AlternativesMannBoschFiltron |
| 03 | Drain plug sealing ringnewFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more.
See manuals →
Step by step
14 steps- Warm the engine up to operating temperature (5-10 minutes), shut it off and wait 5 minutes so the oil drains down into the pan.
- Park the vehicle level over the pit or on the lift and set the parking brake. If there is an engine skid plate, remove it.
- Open the oil filler cap on the engine so the oil drains faster.
- Place the container under the pan and remove the oil pan drain plug. The oil is hot, so be careful not to burn yourself.
- Let the oil drain for at least 10-15 minutes.
- Clean the plug, replace the sealing ring, thread the plug in and tighten it with a torque wrench. Torque is per the manufacturer's specification, approximately 30-50 N·m (22-37 lb-ft). Do not overtighten, as the threads in an aluminum or steel pan are easily stripped.
- Locate the oil filter, place the container under it and unscrew the housing or cartridge. Only a small amount of oil will run out of it.
- Wipe the mounting surface clean. On a new filter, lubricate the sealing ring with clean oil. If the filter is in a housing, replace the housing O-rings as well.
- Install the filter and tighten it. Torque is per the manufacturer's specification (for a spin-on canister, usually hand-tight plus an additional turn; for a cartridge in a housing, use a torque wrench). Do not use excessive force.
- Pour in about 4.5-5 L (4.8-5.3 qt) of oil through the funnel, wait a couple of minutes and check the level on the dipstick.
- Start the engine for 30-60 seconds and wait until the oil pressure light goes out. Shut it off and check for leaks at the plug and the filter.
- After 5 minutes, check the level with the dipstick and top up to the maximum mark. Do not overfill above the MAX mark.
- Reset the service interval counter if the vehicle has one, and take the used oil to a collection point.
- While you are at it, inspect the engine for oil leaks: the valve cover, the crankshaft seals, the oil cooler and its hoses.
Common mistakes and warnings
- Work on a hot but not scorching engine, and use reliable stands under the vehicle rather than only a jack
- Change the oil and filter on schedule per the manufacturer's maintenance schedule
- With city driving, short trips and heavy loads, it is better to shorten the interval
- The torque values above are approximate, so verify the exact values against the manufacturer's specification
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Iveco Brand
Iveco (short for Industrial Vehicles Corporation) is an Italian vehicle manufacturer headquartered in Turin.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →