Autopapyrus · Volkswagen Talagon 2.0 TSI (2021)
https://autopapyrus.com/catalog/volkswagen/talagon/guides/engine-oil-and-oil-filter-replacement/
https://autopapyrus.com/catalog/volkswagen/talagon/guides/engine-oil-and-oil-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Volkswagen Talagon 2.0 TSI (2021): Engine Oil and Oil Filter Replacement
The Volkswagen Talagon with the 2.0 TSI EA888 engine requires an oil change every 10,000 km or once a year per the maintenance schedule. To extend turbocharger life and prevent deposit buildup, shortening the interval to 7,500-8,000 km is recommended. The procedure does not require any special equipment.
Parts
3| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | Oil filterFind on Amazon → | 06L115562A | AlternativesMannMahle OC456 |
| 02 | Drain plug with washer M14×1.5Find on Amazon → | ||
| 03 | Synthetic engine oil5 L (5.3 qt)Find on Amazon → |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
7Step by step
11 steps- Warm the engine up to operating temperature, shut it off, park on level ground and set the parking brake.
- Open the hood, remove the oil filler cap, and pull the dipstick up to release any vacuum.
- Remove the engine undershield: unscrew the Torx T-45 bolts around the perimeter and the Torx T-25 screws in the center mounts, then set the shield aside.
- Place the drain pan under the drain hole and unscrew the drain plug counterclockwise with the T-45 socket. Let the used oil drain completely (5-7 minutes).
- Replace the aluminum washer on the drain plug with a new one and tighten the plug to 25-30 N·m (18-22 lb-ft). Do not overtighten, since the threads in the oil pan are aluminum.
- Loosen the oil filter housing counterclockwise by hand or with a filter wrench, then remove the old filter along with any remaining oil.
- Lubricate the rubber seal of the new filter with clean oil, install the filter in its seat, and screw it in by hand until it contacts the seal, then tighten an additional quarter turn. Do not overtighten with a tool.
- Pour 4.5 L (4.8 qt) of new oil through the filler neck and wait 2-3 minutes for it to drain down.
- Check the level with the dipstick. It should be between MIN and MAX. Top up if needed, to the upper third of the range.
- Start the engine and let it idle for 1-2 minutes. Shut it off, wait 5 minutes, then recheck the level and top up to the proper level.
- Inspect the drain plug and filter for leaks, then reinstall the engine undershield.
Common mistakes and warnings
- Use only oil that meets VW 504.00 or VW 507.00 specifications
- Other standards are not suitable for the turbocharged EA888 engine and can cause accelerated turbocharger wear
- Do not cut corners on the oil filter: counterfeit elements have poor filtering capacity and let abrasive particles into the oil system
- When changing oil on a vehicle with more than 100,000 km, inspect the drain plug for metal shavings
- Their presence may indicate wear of the camshaft or turbocharger
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Volkswagen
Volkswagen proved to the world that a car can be "the people's car": good-looking, affordable and fun.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →