← Ist

Toyota Ist 1.5 1NZ-FE (2007): Engine Oil and Oil Filter Replacement

On the 1NZ-FE, change the oil together with the filter about every 7,000-8,000 km (4,300-5,000 mi). The refill capacity with a filter change is 3.7 L (3.9 qt). The job is done from underneath, with no engine components removed.

DifficultyEasy Time40-60 minutes Steps22

Key figures

  • Drain plug torque
    38 N·m (28 lb-ft). Set it on the torque wrench in step 8; tightening more will strip the threads in the aluminum oil pan
  • Oil filter torque
    17.5 N·m (13 lb-ft) or 3/4 turn after the gasket makes contact (step 13). Too loose and it will leak; too tight and the filter cannot be removed
  • Oil capacity with a filter change
    3.7 L (3.9 qt). This is what you add in steps 14-17; without a filter change, 3.4 L (3.6 qt)
  • Oil viscosity
    SAE 5W-30. It suits all temperatures per the factory schedule; add it in step 14
  • Change interval
    7,000-8,000 km (4,300-5,000 mi). This is how often to change the oil together with the filter

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the oil filter is and how to remove it

View of the filter from below, from under the carcounterclockwiseWithout the filter: what stays on the block2Filter seat on the blockKeep the old filter opening up:oil stays inside it.Put the container under the drain plugat the bottom of the pan.1Filter: unscrew with a wrench3Orange harness and connector4Oil pan at the bottomTap to enlarge
  1. 1Oil filter: the black canister on the engine block. Place a container under it, unscrew it with a filter wrench counterclockwise and keep it opening up, as oil stays inside. Screw the new one on by hand until the gasket touches, then 3/4 turn with the wrench.
  2. 2Filter seat on the block: a round flat surface with a ring groove and a threaded stud in the center. Wipe it with a clean rag and make sure the old rubber gasket did not stay on the engine.
  3. 3Orange corrugated wiring harness and red and white connector next to the filter: a landmark to find the right place. Do not touch them.
  4. 4Oil pan at the bottom of the engine: the drain plug is in it. Put the container under the plug first, then under the filter.

Parts

3
№PartAlternatives
01 SAE 5W-30 engine oil, API SL or higher, energy-conserving4 L (4.2 qt)Find on Amazon →
02 Spin-on oil filter for 1NZ-FE engineFind on Amazon → AlternativesToyotaDensoMannBosch
03 Drain plug gasketnewFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8

Step by step

22 steps · 5 stages
Stage 1 of 5 Preparation 4 steps
  1. Warm up the engine for 3-5 minutes so the oil thins out and drains better. Do not let the engine get very hot, or the hot oil will burn your hands.
  2. Park the car on level ground, set the parking brake and shut off the engine. Raise the car on a lift or position it over an inspection pit. If you use a jack, always place jack stands under the body.
  3. If there is an engine undercover underneath, remove it. It is usually held on by several bolts.
  4. Open the hood and remove the oil filler cap. This lets the oil drain faster.
Stage 2 of 5 Draining the oil and removing the filter 5 steps
  1. Place the drain pan under the drain plug in the oil pan. The pan should hold at least 4-5 L (4.2-5.3 qt).
  2. Remove the drain plug and let the oil drain until it slows to occasional drops, which takes 5-10 minutes.
  3. Wipe the plug and the seat on the oil pan. Remove the old gasket and install a new one.
  4. Thread in the plug and tighten it with a torque wrench to 38 N·m (28 lb-ft). Do not overtighten, because the threads in the aluminum oil pan strip easily.
  5. Move the pan under the oil filter. Unscrew the old filter counterclockwise with the filter wrench. Some oil stays inside, so keep the filter with the opening facing up.
Stage 3 of 5 Installing the new filter 4 steps
  1. Wipe the filter mounting surface with a clean rag. Make sure the old rubber gasket did not stay on the engine.
  2. Lubricate the rubber gasket of the new filter with clean engine oil.
  3. Thread the filter on by hand until the gasket touches the mounting surface.
  4. Then tighten the filter another 3/4 turn with the filter wrench. The tightening torque is 17.5 N·m (13 lb-ft). If you cannot control the torque with the filter wrench, go by 3/4 turn after the gasket makes contact.
Stage 4 of 5 Adding oil 4 steps
  1. Using the funnel, pour in about 3.4 L (3.6 qt) of SAE 5W-30 oil. The factory capacity with a filter change is 3.7 L (3.9 qt). Do not add it all at once; add the rest according to the dipstick.
  2. Close the oil filler cap.
  3. Wait 2-3 minutes for the oil to drain into the pan. Wipe the dipstick, insert it all the way and pull it out. The level should be between the lower and upper marks, closer to the upper one.
  4. Add oil in small amounts until the level reaches the upper mark. Never fill above the upper mark.
Stage 5 of 5 Checking 5 steps
  1. Start the engine and let it run for 1-2 minutes. The oil pressure light should go out 1-2 seconds after startup. If it does not, shut off the engine immediately.
  2. Inspect the drain plug and the oil filter for leaks. If necessary, tighten them, but do not exceed the specified torques.
  3. Shut off the engine and wait 5 minutes. Check the oil level on the dipstick again and top up to the upper mark if needed.
  4. Reinstall the engine undercover. Take the used oil and the old filter to a collection point for used automotive fluids.
  5. Reset the maintenance reminder on the instrument panel, if equipped. Record the mileage of the oil change.

Common mistakes and warnings

  • Do not fill the oil above the upper mark on the dipstick: the excess foams up and increases oil consumption
  • If 5W-30 is not available, 10W-30 will work, but go back to 5W-30 at the next change
  • Used oil is toxic, so wear gloves and do not pour it onto the ground or down a drain
  • The hot engine and the exhaust manifold near the filter can cause burns
Spotted a mistake? Tell us →

Our articles

More articles →