← Uni-S

Changan Uni-S (1st generation, CS55 Plus): Front Door Window Regulator Cable Repair and Slider Replacement

Typical symptoms: the window drops or tilts, you hear cracking and grinding, the motor hums but the window does not move. The plastic sliders and the cable wear out more often than the motor. If the cable is broken or frayed, and the mechanism is riveted or non-serviceable, replacing the complete mechanism is more reliable. Check the actual design on your door after removing the door panel.

DifficultyMedium Time2-3 hours per door Steps14

Key figures

  • Job timeallow this for the door panel, glass and mechanism (steps 3-12)
    2-3 hours per door
  • Masking tapekeep the glass from falling into the door (step 2)
    2-3 strips over the door frame
  • If the window does not work in auto modeso the mechanism relearns its travel (step 13)
    hold the switch for 5-10 seconds at the end positions

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

4
№Part
01 Front door window regulator repair kit (cable, sliders/guides, plastic rollers)for the correct sideFind on Amazon →
02 Front door window regulator assemblywith or without motor; instead of the repair kitFind on Amazon →
03 Door panel clip setif the plastic is brittleFind on Amazon →
04 Butyl tape for door vapor barrierFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

12

Step by step

14 steps
  1. Check the fuse and the window switch. If you can hear the motor running but the window does not move or is tilted, the cause is the cable or the sliders. Turn the ignition off and disconnect the negative battery terminal.
  2. If the window still moves, raise it all the way up. If it has dropped, raise it by hand by the top edge and secure it with masking tape, running 2-3 strips over the top of the door frame. This keeps the glass from dropping into the door and breaking.
  3. Remove the door panel. Remove the screws in the armrest handle, near the inner door release handle and along the bottom edge. Pry the clips around the perimeter with plastic trim tools, then lift the panel upward to release it from the top edge of the inner window seal. Do not yank the panel: wiring harnesses and the handle linkage connect to it.
  4. Photograph the connectors and disconnect them: the switch block, the speaker, the lighting and, if equipped, the sensor in the handle. Disconnect the inner handle rod from the panel.
  5. Carefully peel off the vapor barrier, cutting through the adhesive with a knife. Do not tear the barrier: it has to go back in place. If the adhesive has lost its tack, prepare butyl tape.
  6. Through the service holes, locate the glass-to-carrier attachments (screws, bolts or plastic retainers). Supporting the glass with your hand, loosen the attachment, slide the glass up and secure it to the frame with tape. If the retainer is plastic, release it with a screwdriver through the hole in the glass. The glass is fragile, so support it from below.
  7. Disconnect the motor connector and free the harness from its holders. Remove the mounting screws or nuts of the guide rail and the motor (usually 8-10 mm sockets), or drill out the rivets if the mechanism is riveted. Hold the assembly as you remove it.
  8. Take the mechanism out through the large service opening in the door, taking care not to damage the wires. It is tight in there, so take your time.
  9. Inspect it: a cable that is broken or has slipped off the drum, and crumbled plastic sliders, rollers and guides. If the design allows it, replace the cable and sliders separately, lubricating them with lithium grease. When repairing the cable, keep it seated correctly in the drum grooves and on all the rollers, and make sure it is properly tensioned. If the tension is too low, the cable will jump off; if it is excessive, wear will accelerate.
  10. Clean the guides and lubricate the rail and cable with white lithium grease. Install the mechanism and thread the fasteners by hand, but do not fully tighten them yet. Connect the motor and the switch and temporarily test the mechanism's travel without the glass: it should move smoothly, without binding.
  11. Install the glass onto the carrier, align the holes and secure it. Clamp the glass evenly and moderately, and do not overtighten, as it can crack. Remove the tape.
  12. Reconnect the battery and use the switch: lower and raise the window several times, listening for grinding and checking for tilting. If the glass binds, loosen the fasteners and adjust the position of the guides. Then fully tighten the fasteners: torque values are not published in open sources, so tighten moderately without stripping the threads (as a guideline for small M6 fasteners, about 8-10 N·m (6-7 lb-ft); verify the exact value against the manufacturer's specifications).
  13. Treat the glass seal channels with silicone grease if the travel is stiff. If the auto-up function is not working, hold the switch for 5-10 seconds at the fully down and fully up positions so the mechanism relearns its travel.
  14. Put the vapor barrier back in place (onto butyl tape if needed), reconnect the connectors, hang the panel on the top edge, snap the clips in and install the screws without excessive force. Check the operation of the latch, handles, speaker and window.

Common mistakes and warnings

  • Wear gloves: metal edges inside the door are sharp
  • Disconnect the negative battery terminal before working with the connectors, especially if the door has a side airbag or sensors
  • Do not let the glass fall into the door
  • The exact mechanism mounting layout on the Uni-S and whether the cable and sliders can be replaced separately may vary, and the torque values are approximate, so verify the exact values against the manufacturer's specifications
Spotted a mistake? Tell us →