← Uni-S

Changan Uni-S (First generation, CS55 Plus): Rear Left Brake Caliper Replacement

The rear axle uses an electric parking brake (EPB). Before removing the caliper, the actuator must be put into service mode. Otherwise the piston will not retract, and disconnecting the power can damage the mechanism. After the caliper is installed, the brake line is bled and the actuator is calibrated.

DifficultyMedium Time1.5-2.5 hoursincluding brake bleeding Steps13

Parts

4
№Part
01 Rear left brake caliper assembly with electric parking brake actuator (if the actuator is integrated into the caliper)Find on Amazon →
02 rear brake pad setFind on Amazon →
03 copper or aluminum banjo bolt sealing washersFind on Amazon →
04 DOT 4 brake fluid (caliper and pad aftermarket brands: TRW, Brembo, ATE)Find on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

9

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

13 steps
  1. Park the vehicle on a level surface, select "P," and place wheel chocks under the front wheels. Turn the ignition off. Loosen the lug nuts on the rear left wheel.
  2. Connect a scan tool and activate the EPB service mode (retracting the rear caliper pistons). If you don't have a scan tool, do not disassemble the unit: take the car to a shop that can do this. After the pistons retract, disconnect the actuator connector only with the ignition off.
  3. Raise the rear of the vehicle with a jack, place jack stands under the body, and remove the rear left wheel.
  4. Disconnect the parking brake actuator's electrical connector from the caliper by releasing the locking tab. Pull the wire out of its retainers.
  5. To avoid draining fluid from the reservoir, clamp the brake hose with a brake hose clamp or have plugs ready beforehand. Place a container underneath and undo the banjo bolt that holds the hose to the caliper. Remove the old washers and plug the hose.
  6. Remove the two bolts that secure the caliper to the bracket (or the guide pin bolts, if the bracket stays on) and take off the caliper. Remove the pads and inspect the rotor: if there are deep grooves or a large wear lip, replace the rotors as a pair.
  7. Clean the bracket and guide pins of dirt and apply high-temperature grease to the guide pins. Make sure the dust boots are intact.
  8. Install the pads in the bracket and fit the new caliper (the piston must be fully retracted). Tighten the caliper mounting bolts and the hose banjo bolt with new washers. The torque values are approximate; check the exact values against the manufacturer's specifications: caliper bolts are usually 25-60 N·m (18-44 lb-ft) depending on the design, and the banjo bolt is usually 20-30 N·m (15-22 lb-ft).
  9. Connect the EPB actuator connector and route the wire into its retainers.
  10. Bleed the brake at the rear left wheel: have a helper press the pedal, and release fluid through the bleeder valve until it flows without bubbles, watching the level in the reservoir. Check the bleeding sequence and fluid specification against the manufacturer's specifications (usually DOT 4).
  11. Install the wheel, snug the lug nuts by hand in a crisscross pattern, lower the vehicle, and tighten the nuts with a torque wrench (usually 100-140 N·m (74-103 lb-ft); check the exact value against the manufacturer's specifications).
  12. Using the scan tool, switch the EPB back to normal mode and perform the actuator calibration. Press the brake pedal firmly to the floor several times and check that the pedal is firm.
  13. Test the parking brake by applying and releasing it several times, and make sure there are no fluid leaks. Take a test drive at low speed and check braking performance.

Common mistakes and warnings

  • Brakes are a safety system
  • If you have no experience with brake hydraulics and electric parking brakes, leave the job to a shop
  • Do not force the piston back on a rear axle with an electric actuator: it must be retracted electrically through service mode
  • Do not drive until you have confirmed that the pedal is firm and the parking brake holds
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →