Autopapyrus · Chery Tiggo (1st generation, T11)
https://autopapyrus.com/catalog/chery/tiggo/guides/rear-drive-shaft-axle-shaft-replacement/
https://autopapyrus.com/catalog/chery/tiggo/guides/rear-drive-shaft-axle-shaft-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Chery Tiggo (1st generation, T11): Rear Drive Shaft (Axle Shaft) Replacement
Rear drive shafts are found only on the all-wheel-drive Tiggo T11. The shaft transfers torque from the rear differential to the wheel hub and has an inner and an outer CV joint. Replacement is needed when you hear clicking in turns, feel vibration under acceleration, find torn boots, or see oil leaking from the differential. The exact step-by-step procedure and torque specifications for this model are not confirmed in public sources, so a general procedure is given below. Check all torque values against the manufacturer's specifications.
Parts
4| № | Part |
|---|---|
| 01 | Rear drive shaft (axle shaft) with CV jointsleft or right, correct sideFind on Amazon → |
| 02 | CV joint kit with boots and clampsfor separate shaft repairFind on Amazon → |
| 03 | Rear differential axle shaft sealsFind on Amazon → |
| 04 | Rear differential gear oilFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
10Step by step
16 steps- Make sure the vehicle is all-wheel drive. If the rear axle is not driven, there are no rear shafts, and you should look for the knocking noise in the wheel bearings and suspension. Park the vehicle on level ground, apply the parking brake, and place wheel chocks under the front wheels.
- Loosen the lug nuts on the rear wheel you will remove. Raise the rear of the vehicle with the jack, place jack stands under the body, and remove the wheel.
- Prepare a drain pan. To pull the shaft out of the differential, you usually need to drain the rear differential oil, or at least place a pan underneath, because oil will run out as the shaft comes out of the seal. Remove the fill plug first, then the drain plug. Let the oil drain completely.
- Remove the rear brake components to access the hub. To do this, unbolt the caliper and hang it from the body with wire so the hose carries no load. Then remove the brake rotor. Do not disconnect the brake hoses, so you will not need to bleed the brakes.
- Disconnect the ABS sensor from the hub if it is in the way. Carefully move its wire aside.
- Remove the cotter pin or bend back the lock tab on the hub nut, if there is one. Loosen the shaft nut with an impact socket while holding the hub so it cannot turn. The nut is tightened very tightly.
- Free the hub from the shaft. To do this, disconnect the lower control arm or the steering knuckle from the appropriate suspension arm. Determine which points to disconnect based on the rear suspension design. Move the knuckle outward and, if necessary, drive the outer splined end of the shaft out of the hub with a copper drift.
- Pull the inner end of the shaft out of the rear differential. To do this, pry it with a pry bar near the differential, using a smooth, sharp pull outward. There is a retaining ring inside the joint, so a little force is needed. Do not pull on the boot or bend the shaft.
- Inspect the shaft splines and the seal on the differential. Oil seepage around the seal means the seal must be replaced. Drive the new seal in evenly with a drift, then lubricate its lip with gear oil.
- Compare the new shaft with the old one: the length, number of splines, diameters, and retaining ring type must match. Check that the boots are intact and the clamps are tight.
- Insert the inner end of the new shaft into the differential until you hear a distinct click as the retaining ring seats in its groove. Pull the shaft outward by hand to make sure it stays in place.
- Insert the outer end of the shaft into the hub and reassemble the suspension. Tighten the control arm and knuckle fasteners with a torque wrench to the manufacturer's specified torque. Do the final tightening of the suspension with the vehicle's weight on the wheels if the manufacturer's specifications require it.
- Tighten the shaft nut to the manufacturer's specified torque, then secure it with a cotter pin or lock tab. Install the brake rotor and caliper, and tighten the caliper bolts to specification. Reconnect the ABS sensor.
- Fill the rear differential with oil up to the lower edge of the fill hole, then tighten both plugs. Use the exact capacity and oil grade from the manufacturer's specifications.
- Install the wheel, lower the vehicle, and tighten the lug nuts in a crisscross pattern to the specified torque, usually in the range of 100-130 N·m (74-96 lb-ft) (check the exact value against the manufacturer's specifications).
- Take a test drive. Check for vibration, clicking in turns, and oil leaks at the differential. After 100-200 km, check the wheel nut tightness and make sure there are no leaks.
Common mistakes and warnings
- This job involves the brake system and suspension, and mistakes are dangerous
- If you lack experience, leave it to a repair shop
- All torque values are approximate, so check the exact values against the manufacturer's specifications
- Do not work under a vehicle supported only by a jack: use jack stands
- Replace both shafts if wear is severe, or at least inspect the other one
Spotted a mistake? Tell us →
Our articles
Before you buy
German Turbo Engines vs. Chinese Ones: Which Lasts Longer? An Honest Look at Engine Life
Volkswagen 1.4 and 2.0 TSI, BMW N20 and Mercedes M274 versus Haval, Chery and Geely engines: lifespan benchmarks…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →