https://autopapyrus.com/catalog/ford/fiesta/guides/replacing-the-driver-s-front-seat-belt-retractor-with-pretensioner/
Ford Fiesta (6th generation): Replacing the driver's front seat belt retractor with pretensioner
The Fiesta VI front seat belt is a retractor with a pyrotechnic pretensioner connected to the SRS module. This work involves the passive safety system, and a mistake can result in a belt that does not work or in accidental deployment. If you have no experience working on SRS, have a repair shop do the replacement.
Parts
2| № | Part | Genuine part no. |
|---|---|---|
| 01 | Front left (driver's) seat belt assembly with retractor and pyrotechnic pretensioner, Ford Fiesta VInew only; salvage-yard used belts must not be installedFind on Amazon → | 2038393 |
| 1893975 | ||
| 1893974 | ||
| 02 | Seat belt D-ring (upper guide ring) coverif damagedFind on Amazon → |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
5Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 20 more.
See manuals →
Step by step
11 steps- Turn off the engine and remove the key. Disconnect the negative battery terminal and wait at least one minute so the SRS backup power supply discharges. Do not touch SRS connectors with the ignition on.
- Remove the trim and pillar covers around the belt: the lower B-pillar (center pillar) cover, and if necessary the sill (door threshold) trim and the upper pillar cover. Pry the plastic clips carefully with a trim tool. If clips stay in the body, move them to the trim panels so you do not damage the trim during installation.
- Inspect the belt's D-ring cover. If it is damaged, replace it.
- Remove the upper D-ring (belt guide) bolt on the pillar and take the belt off the ring. Tightening torque on installation: 40 N·m (30 lb-ft).
- Disconnect the pretensioner electrical connector on the retractor. Do not pull on the red locking button. Press it and remove the connector by its housing, otherwise the button will break.
- Remove the lower bolt that secures the retractor to the body and the bolt that secures the belt itself or the buckle tongue (depending on the version). The specified tightening torques are 14 N·m (10 lb-ft) and 40 N·m (30 lb-ft). Which bolt takes which torque depends on the assembly: tighten the retractor bolt and the lower belt anchor to 40 N·m (30 lb-ft), and all other fasteners to 14 N·m (10 lb-ft), unless they are marked otherwise.
- Remove the retractor with the pretensioner from the body. Do not drop, strike or heat it. Do not open the old assembly or throw it out with ordinary trash, because the pretensioner is pyrotechnic. Take it to a repair shop or a disposal facility.
- Install the new belt in reverse order. Make sure the webbing is not twisted and the buckles are accessible to passengers. Tighten the bolts with a torque wrench: 40 N·m (30 lb-ft) on the main mounting points and 14 N·m (10 lb-ft) on those listed above.
- Connect the pretensioner connector until it clicks. Install the pillar covers and clips.
- Reconnect the negative battery terminal. Turn the ignition on and make sure the SRS warning light comes on and then goes out after a few seconds. If the light stays on, read the codes with a scanner that has SRS capability and clear them after fixing the cause.
- Check the belt: pull the webbing out smoothly; it should extend and retract without snagging. Pull the webbing sharply; the mechanism should lock. Check the buckle: the tongue should latch and release with a positive click.
Common mistakes and warnings
- The pretensioner contains a pyrotechnic charge
- Do not use a multimeter on its contacts and do not apply power to the connector
- Work only with the battery disconnected
- If the vehicle has been in a collision and the belt has deployed, replace the belt assembly and check the SRS
- If the SRS light does not go out after replacement, the system needs diagnosis at a repair shop
- Do not drive the vehicle with a faulty belt
- If you are not confident in your abilities or do not have an SRS scanner, take the car to a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Ford
Ford Motor Company is the largest American automaker by heritage and one of the most recognizable car brands in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →