Autopapyrus · Ford Fiesta 1.6 Duratorq TDCi T3JA (2011)
https://autopapyrus.com/catalog/ford/fiesta/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/ford/fiesta/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Ford Fiesta 1.6 Duratorq TDCi T3JA (2011): Engine Oil and Oil Filter Change
On the 1.6 TDCi diesel, the oil and filter are changed together. The filter is not a spin-on canister. It is a paper element inside a plastic cap housing on top of the engine. The factory interval is up to 12,500 miles, but for a diesel it makes sense to change it every 10,000 km or once a year, and more often if you mostly make short trips or drive in the city.
Key figures
- Drain plug tightening torqueabout 35 N·m (26 lb-ft). Set it on the torque wrench in step 7. Too loose and it will leak oil, too tight and you will strip the threads in the oil pan.
- Oil filter cap tightening torqueabout 25 N·m (18 lb-ft). Step 10. The cap is plastic, and overtightening can break it.
- Oil capacity with a filter changeabout 3.9 L (4.1 qt). Step 11. Add the oil in stages and check the level on the dipstick.
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
4| № | Part | Alternatives |
|---|---|---|
| 01 | 5W-30 engine oil, Ford WSS-M2C913-Cabout 4 L (4.2 qt)Find on Amazon → | |
| 02 | Oil filter for 1.6 TDCi (replaceable paper element in housing cap)Find on Amazon → | AlternativesMannBoschFiltron |
| 03 | Oil filter cap O-ringsusually included with the filter elementFind on Amazon → | |
| 04 | Drain plug sealing washernewFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8- Jack and two jack stands (or an inspection pit) Amazon →
- socket for the oil pan drain plug (confirm the size on your plug, usually 13-17 mm) Amazon →
- torque wrench Amazon →
- socket or puller for the oil filter cap Amazon →
- 5-6 L (5.3-6.3 qt) container for used oil Amazon →
- funnel Amazon →
- shop rags Amazon →
- gloves Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 20 more.
See manuals →
Step by step
15 steps- Warm the engine up to operating temperature (5-10 minutes of driving), then shut it off. Hot oil flows better, but drain it carefully because it can burn you.
- Park the car on level ground. If you need access from below, raise the front with a jack and always support it with jack stands. Never work under a car supported only by a jack.
- Open the hood and find the round oil filter cap on the engine (on top of the engine, next to the plastic cover). If necessary, remove the decorative engine cover.
- Pull out the oil dipstick and unscrew the oil filler cap, so the oil drains faster.
- Remove the lower engine undercover if one is fitted. Place the container under the oil pan.
- Remove the oil pan drain plug and drain the oil completely (10-15 minutes). Wipe the plug and its seat.
- Replace the drain plug sealing washer, install the plug and tighten it to about 35 N·m (26 lb-ft).
- Place rags under the filter cap so oil doesn't run into the engine bay. Unscrew the filter cap together with the element.
- Remove the used element from the cap. Replace the O-rings on the cap and on the housing, and lightly lubricate them with fresh oil. Make sure no old O-ring is left in the seat.
- Install the new element in the cap, insert it into the housing and tighten the cap to about 25 N·m (18 lb-ft). Do not overtighten, because the cap is plastic.
- Add fresh oil: about 3.9 L (4.1 qt) with the filter change. First add about 3.5 L (3.7 qt), wait a minute and check the level with the dipstick, then top up to the MAX mark, but not above it.
- Close the oil filler cap and insert the dipstick. Start the engine for 30-60 seconds: the oil pressure light should go out within a few seconds after startup.
- Shut off the engine and check the drain plug and filter cap for leaks. After 5 minutes, check the level with the dipstick and top up to MAX if needed.
- Install the undercover and the decorative cover, then lower the car. Dispose of the used oil at a collection point.
- Reset the service interval indicator if your instrument cluster has one, and record the mileage of the oil change.
Common mistakes and warnings
- Do not use oil that lacks the Ford WSS-M2C913 approval (low-ash 5W-30)
- On diesels with a particulate filter, the wrong oil shortens the life of the filter and the turbocharger
- The capacity and torque values (35 N·m (26 lb-ft) for the drain plug, 25 N·m (18 lb-ft) for the filter cap) are based on data for diesel Fiestas of this generation
- Check the exact values for your car against the manufacturer's specifications
- Do not exceed the MAX level: overfilling harms the particulate filter and the seals
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Ford
Ford Motor Company is the largest American automaker by heritage and one of the most recognizable car brands in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →