https://autopapyrus.com/catalog/ford/focus/guides/replacing-and-adjusting-the-manual-transmission-shift-cables/
Ford Focus IV (2019): Removing, Installing and Adjusting the Shift Cables
This guide covers a manual transmission, where shifting is controlled by two cables: a shift cable and a gear selector cable. After replacing or disconnecting the cables, you must adjust them to the neutral position. On 2019 vehicles with an automatic transmission, the selector is usually electronic and has no cable, so this guide does not apply to them.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Manual transmission cable set (shift cable and gear selector cable) with end fittings and thrust bushingsFind on Amazon → | AlternativesFordFebiSachs |
| 02 | Downpipe flange gasketnewFind on Amazon → | |
| 03 | Cable bracket bushing repair kitFind on Amazon → | AlternativesFordFebiSachs |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- Lift or inspection pit Amazon →
- socket and wrench set Amazon →
- plastic trim removal tools Amazon →
- screwdrivers Amazon →
- knife for cutting the sound insulation Amazon →
- wire for hanging the exhaust pipe Amazon →
- cord or thin cable for pulling the new cables through Amazon →
- masking tape or adhesive tape Amazon →
- new exhaust flange gasket Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 25 more.
See manuals →
Step by step
35 steps · 7 stagesStage 1 of 7 Preparation and diagnosis 4 steps
- Check for symptoms: vague gear engagement, play or wobble in the lever, inability to engage a gear, or a lever that is off-center in neutral. Inspect the rubber bushings and cable end fittings for wear and cracks. Sometimes it is enough to replace the bushings and adjust the cables.
- Park the car on level ground, put the lever in neutral, apply the parking brake and chock the wheels.
- Disconnect the negative battery terminal. Wait at least 5 minutes.
- Remove the air filter with its ducts and the battery tray if they block access to the cable bracket on the transmission. The removal order depends on the engine.
Stage 2 of 7 Access in the cabin 4 steps
- Remove the shift knob (pull it up or unscrew it, depending on the design) and the lever trim. Disconnect the connectors, if any (the number depends on trim level).
- Remove the center console by releasing the clips and mounting screws. Disconnect the console connectors.
- Remove the rear footwell heating duct under the console if it blocks access to the base of the lever.
- Remove the trim panels and fold back the carpet and sound insulation from the tunnel to expose the cable bracket and the seal where the cables enter the cabin. If needed, cut the sound insulation with a knife and fold it back.
Stage 3 of 7 Removal at the transmission end 7 steps
- Raise the car on the lift. Leave the lever in neutral.
- Remove the underbody shield, if fitted.
- Disconnect the exhaust pipe flange from the downpipe and take the pipe off its rubber hangers. Disconnect the center hanger, lower the system and hang it with wire. Do not bend the flex section, to avoid damaging it.
- Remove the fasteners and take off the tunnel heat shield.
- Release the cables from the clips on the underbody.
- Press the locking tab and remove the shift cable from the lever on the transmission. Remove the gear selector cable the same way. Note which cable goes on which lever: they have different end fitting colors or markings.
- Pull the cable thrust bushings back and remove the cables from the bracket on the transmission.
Stage 4 of 7 Removal at the cabin end and cable removal 4 steps
- In the cabin, carefully and without jerking, pry off and remove the cable end fittings from the levers of the shift mechanism. To do this, slide the thrust bushings forward.
- Remove the two nuts of the cable bracket on the body and take the bracket off the floor.
- Tie a cord to the end of each cable at the transmission so you can pull the new ones along the same path later.
- Pull the cables into the cabin through the floor after removing the grommet seal. Remove the set.
Stage 5 of 7 Installation 7 steps
- Compare the new cables with the old ones by length, end fittings and colors.
- Tie the cord to the new cable and pull it from the cabin downward along the old path. Make sure there are no sharp bends or twisting.
- Install the seal in the floor and secure the cable bracket with the nuts. Approximate tightening torque for the bracket nuts is 8-10 N·m (6-7 lb-ft); check the exact value against the manufacturer's specification.
- Push the cable end fittings onto the shift mechanism levers in the cabin until they click. Install the thrust bushings.
- Connect the cables to the levers on the transmission and lock them in the bracket until you hear a distinct click. Check that the bushings are fully seated and the cable is not twisted.
- Secure the cables in the underbody clips and install the heat shield.
- Secure the exhaust pipe on its hangers. Install the flange on a new gasket. Approximate flange tightening torque is 40-50 N·m (30-37 lb-ft); check the exact value against the manufacturer's specification. Remove the hanging wire.
Stage 6 of 7 Adjustment 4 steps
- The lever must be in neutral with the parking brake applied. Release the adjustment lock on the gear selector cable.
- Move the lever into 4th gear. This locks the small lever on the transmission in the neutral position.
- Press the gear selector cable lock back in to secure the adjustment at the small lever.
- Return the lever to neutral and check that it sits in the center and does not fall to either side.
Stage 7 of 7 Reassembly and check 5 steps
- Tape up the cut in the sound insulation with masking tape or adhesive tape and lay the carpet back in place.
- Install the duct, center console, lever trim and shift knob, and reconnect the connectors.
- Install the battery tray and air filter if you removed them. Connect the negative battery terminal.
- Lower the car, start the engine, press the clutch and shift through all gears several times, including reverse. Gears should engage cleanly, without effort or grinding.
- Take a test drive and check shifting in every gear. If engagement is vague, repeat the adjustment following steps 27-30.
Common mistakes and warnings
- The exhaust system gets hot, so work only on a cooled-down car
- When working under a raised car, use a lift or reliable stands
- The torque values above are approximate, so check the exact values against the manufacturer's specification
- If you are not sure about taking the console apart, contact a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Ford
Ford Motor Company is the largest American automaker by heritage and one of the most recognizable car brands in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →