Autopapyrus · Ford Transit 2.2 TDCi 125 hp (2021)
https://autopapyrus.com/catalog/ford/transit/guides/battery-replacement/
https://autopapyrus.com/catalog/ford/transit/guides/battery-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Ford Transit 2.2 TDCi 125 hp (2021): Battery Replacement
The battery sits in the engine bay under a protective cover. Replacement comes down to removing the cover, disconnecting the terminals, removing the hold-down and installing the new battery. The main thing is to follow the terminal order and, after replacement, let the electronics "get used to" the new power supply.
Key figures
- Terminal socket10 mm. A 10 mm socket with a ratchet fits the clamps on both terminals (steps 4, 5, 11, 12)
- Voltage of a good, charged batteryabout 12.6 V. Measure it with a multimeter across the posts after installation (step 13)
- Battery length278, 315 or 353 mm with a width of 175 mm. Choose a new battery of the same dimensions so it fits the tray (section "Part")
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | 12 V battery, standard polarity (positive on right), standard terminals, 74–95 Ahlength 278, 315 or 353 mm, width 175 mm; with Start-Stop — AGM or EFB typeFind on Amazon → | AlternativesVartaBoschExide |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 15 more.
See manuals →
Step by step
15 steps- Shut off the engine, remove the key and close all the doors. If you have a keyless entry fob, take it well away from the vehicle. Write down or photograph the radio and clock settings if they don't restore themselves.
- Open the hood and remove the plastic cover from the battery compartment. It is usually held by clips or a single screw.
- Inspect the battery. Note how the terminals are positioned, where the vent hose runs (if there is one) and how the cables are routed. It's best to take a photo.
- Disconnect the negative (black) terminal first. Loosen its clamp with the 10 mm socket and pull the terminal off the post. Move the cable aside so it can't accidentally touch the post. If the negative terminal has a battery monitoring sensor (a module on the terminal), don't pull it by its wires. Remove it together with the terminal.
- Then disconnect the positive (red) terminal. First slide the protective cap back, then loosen the clamp with the 10 mm socket and pull the terminal off.
- Remove the battery hold-down. This is the bracket or strap that presses the battery against the tray. Undo the bolt, remove the bracket and set the hardware aside so you don't lose it.
- Lift out the battery, holding it by the case with both hands. It is heavy, up to 20-25 kg (44-55 lb) for high-capacity versions. Keep it upright so you don't spill electrolyte, and don't tilt it.
- Clean the tray and terminals with a brush. If there is white or green corrosion on the cables, scrape it off. Wipe the tray with a dry rag.
- Set the new battery in the tray in the same orientation. The posts must end up the same as before: positive on the right when viewed from the terminal side, like the original battery.
- Install the hold-down bracket and tighten its bolt so the battery can't be moved by hand. Don't overtighten, as you can crack the case. Tightening torque: per the manufacturer's specification.
- Connect the positive terminal first. Push it onto the post all the way and tighten the clamp with the 10 mm socket. The terminal torque is low, per the manufacturer's specification. Tighten until the terminal no longer turns by hand. Don't use heavy force, since lead posts are soft. Put the protective cap back in place.
- Then connect the negative terminal the same way.
- Wiggle both terminals by hand. They must not move. Check the voltage across the posts with a multimeter. A good, charged battery reads about 12.6 V.
- Turn the ignition on, wait a few seconds and start the engine. The clock, radio and onboard computer may need to be set again. Power windows sometimes need to be relearned (hold the switch up until the window stops, then keep holding it for a couple more seconds).
- Put the battery compartment cover back and close the hood. Take the old battery to a recycling point or to the store where you bought the new one.
Common mistakes and warnings
- Don't short the posts with a tool
- A wrench touching the positive post and the body at the same time produces a strong spark and can cause burns or damage the wiring
- Remove jewelry and wear gloves and safety glasses
- Electrolyte is corrosive, and charging releases explosive gas, so keep flames and smoking away
- If the vehicle has Start-Stop or a battery monitoring system, install a battery of the same type (AGM or EFB) as the factory one
- An unsuitable battery fails quickly, and the charging system may not work correctly
- For such vehicles, it is best to "register" the new battery in the system with a diagnostic scan tool
- This resets the battery state data, and a repair shop can do it if you don't have a scan tool
- The torque values in this guide are approximate, so check the exact values against the manufacturer's specification
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Ford
Ford Motor Company is the largest American automaker by heritage and one of the most recognizable car brands in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →