https://autopapyrus.com/catalog/ford/transit/guides/fuel-injector-replacement/
Ford Transit 2.2 TDCi 125 hp (2014): Fuel Injector Replacement
The 2.2 TDCi injectors are part of a solenoid-controlled Common Rail system. After replacement, each new injector must be coded (programming of its individual calibration code) into the engine control unit. The job demands extreme cleanliness: not a speck of dirt may get into the high-pressure system.
Parts
7| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | Common Rail fuel injector, 2.2 TDCi Duratorq (Puma) 125 hp4 pcs.Find on Amazon → | 1746967 | AlternativesDelphiBosch |
| 1840747 | |||
| 2079601 | |||
| 02 | Copper injector sealing washer4 pcs.Find on Amazon → | ||
| 03 | Injector heat shield washer or seal ringif not included in the setFind on Amazon → | 1745686 | |
| 1854206 | |||
| 1673574 | |||
| 04 | Injector return line sealFind on Amazon → | ||
| 05 | Valve cover gasketFind on Amazon → | 1848542 | |
| 06 | Fuel filterrecommended to replace at the same timeFind on Amazon → | ||
| 07 | High-pressure fuel linesif neededFind on Amazon → | 1717574 | |
| 2073143 | |||
| 2073157 |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
9- Socket set and ratchet Amazon →
- torque wrench Amazon →
- flare-nut (split) wrenches for high-pressure lines Amazon →
- injector puller or slide hammer for Duratorq injectors Amazon →
- socket for the injector hold-down clamp Amazon →
- brush and clean lint-free cloth Amazon →
- caps/plugs for fuel fittings Amazon →
- scan tool with injector coding (calibration code programming) function Amazon →
- syringe or container for fuel Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 15 more.
See manuals →
Step by step
15 steps- Determine the cause of the problem: check the control unit for fault codes with a scan tool, and check cylinder balance, correction values and return flow for each injector. Replace injectors only after confirmed diagnosis, not just because of smoky exhaust.
- Disconnect the negative battery terminal and wait a few minutes. Shut off the engine and let it cool down. The system is under high pressure: do not disconnect fuel lines on a running engine or one that has just been shut off.
- Remove the engine cover, air ducts and anything else that blocks access to the valve cover and the fuel rail. Thoroughly clean the injectors, the rail and the surrounding area with a brush and compressed air while everything is still assembled.
- Disconnect the injector electrical connectors (carefully press the connector lock; the plastic on older engines is brittle) and label them by cylinder.
- Disconnect the injector return line. Use caps on the open fittings so fuel does not leak out and dirt does not get inside.
- Loosen and remove the high-pressure lines from the rail to the injectors (with a flare-nut wrench, without excessive force). If you reuse used lines, check the cone for deformation and replace them if in doubt. Immediately cap all open fittings.
- Remove the valve cover if you cannot reach the injector hold-down clamps without doing so.
- Remove the bolt and the hold-down clamp of each injector. Pull out the injector: if it is stuck, use a special slide-hammer puller. Do not pry it with a pry bar or knock it out with a hammer, since it is easy to damage the seat in the cylinder head.
- Clean the injector bores in the cylinder head of carbon and deposits with a special tool or a soft brush, without dropping anything into the cylinder. Make sure the old copper washer came out with the injector and did not stay at the bottom of the bore.
- Install the new injectors with new copper washers on the tip. Seat each injector straight, without tilting. Install the hold-down clamps and tighten the bolts in several stages to the manufacturer's specified torque (Duratorq injector clamps use a low torque plus, if required, an angle turn; check the exact value against the data for your engine).
- Install the high-pressure lines. First thread the nuts on by hand and make sure the cone seats without tilting, then tighten with a torque wrench to spec (typically about 25-30 N·m (18-22 lb-ft) for these fittings, but use the exact manufacturer's value).
- Reconnect the injector return line with new seals and the electrical connectors, then install the valve cover with a new gasket (tighten the bolts evenly, in sequence, to a low torque per spec) and refit the removed parts.
- Replace the fuel filter, fill the system with fuel and prime it with the hand pump (if equipped) until you feel firm resistance. Reconnect the battery.
- Connect the scan tool and program the codes (calibration values) of each new injector according to the cylinder it is installed in. Without this the engine will run roughly, smoke, and may not start.
- Crank the engine with the starter without starting it for 10-15 seconds to purge air, then start the engine. With the engine running, check for fuel leaks around the lines, the rail and the return line (visually, at low rpm only, never with your hand). Clear the fault codes and take a test drive.
Common mistakes and warnings
- Fuel in the rail is under very high pressure (hundreds of bar at idle), and a jet can penetrate the skin
- Never open fuel lines on a running engine
- If you have no experience with Common Rail systems and no equipment for coding injectors, leave the job to a specialist repair shop
- After replacement, all new injectors must be coded, and seized old injectors should be removed only with a puller
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Ford
Ford Motor Company is the largest American automaker by heritage and one of the most recognizable car brands in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →