Autopapyrus · Hyundai Santa Fe 2.2 CRDi D4HB (2019)
https://autopapyrus.com/catalog/hyundai/santa-fe/guides/intake-manifold-removal-gasket-and-hose-replacement/
https://autopapyrus.com/catalog/hyundai/santa-fe/guides/intake-manifold-removal-gasket-and-hose-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Hyundai Santa Fe 2.2 CRDi D4HB (2019): Intake Manifold Removal, Gasket and Hose Replacement
On the D4HB, an air leak is most often caused by a loose intercooler hose connection, a cracked hose, or a throttle body seal that has lost its elasticity. The manifold gasket is less often to blame. The manifold is hard to remove: some of its fasteners are located underneath it, and you have to undo them by feel. Check and replace the hoses first, and remove the manifold only if the leak remains.
Key figures
- Manifold fastenersthe number to remove and later reinstall in step 9, some are underneath the manifold and must be found by feel7 bolts and 2 nuts
- EGR tube mountingin step 7, do not damage the rubber O-ring on the tube2 bolts from below
- Wiring harness mountingstep 5, the harness must be set aside2 bolts plus 1 bolt and 1 nut near the battery
- Air intake housing mountingstep 3, removes without tools2 clips
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
7| № | Part |
|---|---|
| 01 | Intake manifold gasket (D4HB)Find on Amazon → |
| 02 | Throttle body O-ringFind on Amazon → |
| 03 | EGR tube O-ringsFind on Amazon → |
| 04 | Upper intercooler hoseif worn or crackedFind on Amazon → |
| 05 | Lower intercooler hoseif worn or crackedFind on Amazon → |
| 06 | Intercooler hose clampsif worn or crackedFind on Amazon → |
| 07 | Hyundai coolantfor topping offFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 6 more.
See manuals →
Step by step
14 steps- Find the source of the air leak. Check the intercooler hoses and the plastic air intake housing for oil streaks, cracks, and joints that have shifted. A typical weak point on the D4HB is the mounting of the intercooler inlet hose, which can pop off under hard acceleration. Traces of oil at the joints show where air is escaping. Heavy dust on the MAF sensor and boost pressure codes (for example, P0299) also point to an intake leak. If the hoses are intact, move on to pressure testing the intake: apply low air pressure and brush soapy water on the joints. Keep the pressure low and take the exact value from the manufacturer's specification.
- Shut off the engine and let it cool down. Disconnect the negative battery terminal. For convenience, you can remove the battery completely.
- Remove the plastic air intake housing: it is held on by two clips. Remove the upper intercooler hose. Inspect the hoses and clamps, and replace any that are cracked or hardened. When reinstalling, seat the hose all the way on and tighten the clamp securely.
- Disconnect the hose from the throttle body. It sits on a retainer that you open with a screwdriver. Unplug the throttle body power connector and remove the throttle body. According to owner reports, it is held by two bolts and two nuts. Other D4HB engines have a layout of three bolts and one nut, so count the fasteners on your engine. Replace the throttle body O-ring.
- Photograph and disconnect all sensor and injector connectors on the wiring harness near the manifold. The connectors are different, but the photos will make reassembly easier. Remove the two bolts holding the harness and the one bolt and nut near the battery. Set the harness aside.
- Cover all the fuel fittings you will open with clean plastic film or caps. Remove the fuel line between the rail and the high-pressure pump with a flare nut wrench. Disconnect the two fuel connectors on the high-pressure pump. Dirt in the fuel system is dangerous for the injectors.
- Remove the two lower bolts of the EGR tube. It can be removed together with the manifold and separated later on the bench. Do not lose or damage the small rubber O-ring.
- Remove the sensors and small fuel hose brackets that get in the manifold's way. Drain some of the coolant or pump it out of the expansion tank so you can disconnect the coolant tube. Pull out the plastic pipe that obstructs the manifold by turning it slightly as you pull.
- Unbolt the manifold: 7 bolts and 2 nuts. Some of the fasteners are underneath, and you have to find them by hand. Use a swivel joint and extensions. Remove the manifold. Remove the swirl flap sensor and actuator from it only if it needs cleaning or replacement.
- Clean the cylinder head mating surface of any remaining old gasket material, and keep debris out of the intake ports (cover them with a clean rag, then remove it). Inspect the manifold passages: if there is carbon buildup or oily sludge, clean them with cleaner and a soft brush. Check that the swirl flaps move freely.
- Install the new manifold gasket. Guide the manifold into place, keeping the EGR tube and the coolant tube in mind. Tighten the fasteners evenly from the center outward with a torque wrench. The torque for the manifold bolts and nuts is not given in public sources. For manifolds of this size it is usually 15-25 N·m (11-18 lb-ft), but take the exact value from the manufacturer's specification.
- Reassemble everything in reverse order: the EGR tube with new O-rings, the rail-to-high-pressure-pump fuel line, the pump connectors, the harness, the throttle body with a new O-ring, the hoses, the intercooler hose, and the air intake housing. Tighten the remaining fasteners per the manufacturer's specification, and tighten small bolts without excessive force so you don't strip the threads.
- Top off the coolant to the proper level. Connect the battery. Before starting, turn the ignition on and off several times so the pump primes the fuel system. Sometimes it also helps to jumper the fuel pump relay contacts for 2-3 minutes with the ignition on. The first start may take a few seconds longer than usual.
- Warm up the engine and check for coolant and fuel leaks and for air leaks (unusual whistling sounds). Read the codes with a scan tool and clear them. Take a test drive that includes acceleration, and check that boost pressure is normal and there are no hesitations.
Common mistakes and warnings
- Working on the high-pressure fuel system requires care: open fuel lines only on a cold engine and keep everything clean, otherwise contamination will damage the injectors and the high-pressure pump
- Do not start the engine if the EGR tube, throttle body, or hoses are not fully tightened
- If you have little experience and are unsure about reaching the fasteners under the manifold, leave the job to a repair shop
Spotted a mistake? Tell us →
Test yourself
Our articles
Brand stories
The History of Hyundai
Hyundai Motor Company, whose name means "modernity" in Korean, is South Korea's largest automaker and one of the top…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →