← Solaris

Hyundai Solaris (Accent) 1.4/1.6 (2012): Rear Drum Brake Shoe Replacement

First-generation (RB) 2012 Solaris (Accent) vehicles have drum brakes at the rear. The shoes are replaced on both wheels of the rear axle at the same time; the assembly you removed from the first wheel serves as a reference for reassembly on the second wheel. Replacing the shoes changes the adjuster position, so at the end you need to readjust and check the parking brake. The procedure for the front pads is different.

DifficultyMedium Time1.5-2.5 hours Steps31

Key figures

  • Lug nut torque
    about 108 N·m (80 lb-ft). Set it with a torque wrench in step 27; under-tightening is dangerous, as the wheel may come loose.
  • Lug nut wrench
    21 mm socket. Used in steps 2 and 27.
  • Minimum shoe lining thickness
    about 1 mm. Measure in step 12; if less remains, the shoes need replacing.
  • Maximum drum diameter
    about 204 mm (8.04 in). Measure in step 13; if exceeded, the drum needs replacing.

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the springs, adjuster and shoes of the rear drum brake are and what to do with them

Rear brake with the drum removedWheel and drum removed, looking at the backing plate with the shoes1Shoes with lining2Upper return spring3Adjuster star wheel4Wheel cylinder5Hold-down springs (two)6Lower return spring7Lower shoe anchorTap to enlarge
  1. 1Two shoes with lining: the top ends press on the cylinder pistons, the bottom ends rest on the anchor. Remove and replace them, always on both wheels of the axle.
  2. 2Upper return spring: two coil springs at the sides of the cylinder and the adjuster. Remove with pliers or cutters, and on the new shoes fit it as on the other wheel.
  3. 3Adjuster with star wheel: a threaded rod and lever right under the cylinder. Clean it, grease the thread and rod end, fit it fully retracted, and at the end adjust with the star wheel through the hole in the plate.
  4. 4Wheel cylinder with boots: its pistons push on the top ends of the shoes. Brake fluid leaks under the boots are a reason to replace the cylinder. Do not press the pedal with the drums removed.
  5. 5Hold-down springs with cup (two, one per shoe): squeeze the cup with pliers, turn it 90° until the slots line up with the pin, then remove the cup, spring and pin.
  6. 6Lower return spring: runs from shoe to shoe at the lower anchor. Remove it after the upper one, and on the new shoes fit it first, copying the other wheel.
  7. 7Lower shoe anchor: the bottom ends of the shoes rest on it. Clean the plate with a wire brush and lightly grease the support pads with brake grease.

Parts

4
№PartAlternatives
01 Rear drum brake shoe set, Hyundai Solaris (4 shoes)1 set per axleFind on Amazon → AlternativesNisshinboSangsin (Hi-Q)HSBMobis
02 Rear brake shoe installation kit (springs, hold-down pins)recommended if the springs are wornFind on Amazon →
03 Rear brake drumspair, if there are drum problemsFind on Amazon →
04 Rear wheel cylindersif faultyFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

16

Step by step

31 steps · 6 stages
Stage 1 of 6 Preparation 3 steps
  1. Park the vehicle on a level, firm surface and chock the front wheels. Do NOT engage the parking brake (a drum with a tensioned cable will not come off).
  2. Loosen the lug nuts on the rear wheels about half a turn with a 21 mm socket.
  3. Raise the rear of the vehicle with the jack, set it on jack stands, and remove both rear wheels.
Stage 2 of 6 Drum removal and shoe disassembly 8 steps
  1. Remove the drum retaining screw. If it is seized, use an impact screwdriver: strike it while turning it at the same time.
  2. Remove the drum. If it does not come off, tap the end face of the drum with a mallet (not the wheel rim). If the fit is tight, you can thread bolts into the threaded holes in the drum and push it off.
  3. Do not disassemble both wheels at the same time: leave the drum and assembly on the other wheel as a reference.
  4. Clean the assembly with brake cleaner (place a drip pan underneath). Do not inhale the dust and do not blow it off with compressed air.
  5. Remove the upper return spring between the shoes (with pliers or side cutters), then the lower spring and the adjuster lever spring.
  6. Take out the strut/adjuster bar between the shoes and spread the shoes apart.
  7. Remove the shoe hold-down springs: squeeze the cup with pliers, turn it 90° until the slots line up with the pin, remove the cup and spring, and take out the pin.
  8. Clamp the parking brake cable with locking pliers (so it does not slip back into the backing plate), disconnect it from the shoe lever, and remove the shoes.
Stage 3 of 6 Inspection and cleaning 5 steps
  1. Measure the lining thickness: replace the shoes when less than about 1 mm remains; always replace both sides.
  2. Measure the inside diameter of the drum in several directions. The readings should match; replace the drum if it exceeds the maximum diameter (about 204 mm for drums of this size; the exact value is stamped on the drum), or if it has deep grooves, cracks, or glazed spots. Minor defects can be machined out.
  3. Inspect the wheel cylinder: brake fluid leaking from under the dust boots is a reason to replace the cylinder.
  4. Clean the backing plate with a wire brush, especially the pads the shoes slide on. Disassemble the strut adjuster (star wheel), clean it with brake cleaner, and lubricate the threads and the end of the stem with brake grease.
  5. Apply a thin layer of grease to the support pads on the backing plate, to the points where the shoes contact the cylinder pistons, to the parking brake lever, and to the pins. Grease must not get on the linings, the drum, or the friction surface.
Stage 4 of 6 Installing the new shoes 7 steps
  1. Connect the parking brake cable to the lever on the new shoe before mounting it on the backing plate (hold the cable with the clamp).
  2. Install the first shoe: pass the pin through the backing plate from behind, fit the spring and cup, and turn 90° to lock.
  3. Install the second shoe the same way (nothing holds it in place yet, so support it by hand).
  4. Install the strut adjuster in its fully retracted position (this makes assembly easier).
  5. Fit the lower return spring, then the upper one and the adjuster lever spring, using the other wheel as a reference.
  6. Check against the reference that the springs and levers are positioned the same way, the shoes rest on their supports, and the cable moves freely.
  7. Wipe the inside of the drum with brake cleaner (no oil should remain on it) and let it dry.
Stage 5 of 6 Reassembly and adjustment 4 steps
  1. Fit the drum, line up the screw hole, and tighten the retaining screw.
  2. Through the access hole in the backing plate (remove the rubber plug), use a bent screwdriver to turn the adjuster star wheel until the shoes just begin to lightly touch the drum (a light scraping sound when turning it). Put the plug back.
  3. Repeat steps 4-25 on the other wheel.
  4. Install the wheels and tighten the nuts in a crisscross pattern. Lug nut torque is about 108 N·m (80 lb-ft); tighten with a torque wrench after lowering the vehicle to the ground.
Stage 6 of 6 Checking 4 steps
  1. Press the brake pedal firmly to the floor several times. The adjuster will set the clearance, and the pedal should become firm.
  2. Check the parking brake: the lever should engage within a few clicks, and the wheels should not turn when it is applied. If necessary, adjust the cable tension with the nut on the lever.
  3. Check the brake fluid level in the reservoir (it should not be below MIN) and make sure there are no leaks at the cylinders.
  4. Take a test drive at low speed: the vehicle should brake without pulling to one side and without unusual noise. New shoes need a few hundred kilometers to bed in; avoid hard braking during this time.

Common mistakes and warnings

  • The brake system is a safety-critical assembly: if you lack experience, have a repair shop do the work
  • Do not inhale brake dust, and always replace the shoes on both wheels of the axle at the same time
  • Do not press the brake pedal with the drums removed, as the wheel cylinder pistons may pop out
  • Never work under the vehicle without jack stands
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →