https://autopapyrus.com/catalog/hyundai/tucson/guides/rear-brake-disc-and-pad-replacement/
Hyundai Tucson IV (NX4) (2024): Rear Brake Disc and Pad Replacement
On the Tucson NX4, the rear calipers have an electric parking brake (EPB), so you must put it into service mode before removing the caliper. Otherwise the piston will not retract and you could damage the actuator. Replace the discs and pads as a set on both sides of the axle. The torque values below are approximate, so check the exact figures against the manufacturer's specifications.
Diagram: where the rear caliper, bracket, pads and disc are
- 1Caliper: cast body with a bridge over the disc. Remove it after the guide bolts and hang it on the spring or wire.
- 2Two caliper guide bolts with a 14 mm hex head. If the pin spins, hold it with a 17 mm wrench.
- 3Caliper bracket with two 14 mm bolts. Remove it after the caliper and pads, use non-impact tools.
- 4Brake pads in the caliper window. The pad with the wear sensor goes on the inner side.
- 5Brake disc: removed after the bracket, replaced as an axle set. Tap a stuck disc on the hub part.
- 6Small cross-head disc screw, much smaller than the wheel studs. Remove it with a PH3 screwdriver.
- 7Brake hose: do not disconnect or stretch it, hang the caliper so the hose is not pulled.
Parts
4| № | Part | Alternatives |
|---|---|---|
| 01 | Rear brake discs (vented or solid)set per axleFind on Amazon → | AlternativesBremboTRWTextarMando |
| 02 | Rear brake pads with spring clips and retainerssetFind on Amazon → | AlternativesBremboTRWTextarMando |
| 03 | Caliper guide pin greaseFind on Amazon → | |
| 04 | Caliper guide boltsif neededFind on Amazon → | AlternativesBremboTRWTextarMando |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
11- Jack and two jack stands Amazon →
- 21 mm lug wrench Amazon →
- 14 mm and 17 mm sockets and wrenches Amazon →
- torque wrench Amazon →
- Phillips screwdriver (PH3) Amazon →
- hammer Amazon →
- wire brush Amazon →
- brake cleaner Amazon →
- C-clamp or a rotating piston reset tool Amazon →
- thin layer of high-temperature grease for the guide pins Amazon →
- scan tool or the factory EPB service mode Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more.
See manuals →
Step by step
22 steps · 4 stagesStage 1 of 4 Preparation 4 steps
- Park the vehicle on level ground, put it in P, and chock the front wheels. Loosen the rear wheel lug nuts half a turn with a 21 mm wrench.
- Put the rear calipers into EPB service mode (using the factory procedure or a scan tool) and wait for the actuators to retract the pistons. Then turn the ignition off and keep the EPB from receiving any further commands: do not press the parking brake switch or the brake pedal until the work is finished.
- Raise the rear axle with the jack, set the jack stands, and remove the wheel.
- Inspect the condition of the parts: the thickness of the discs and pads, the dust boots, and the hoses. If the pads have 2 mm or less of friction material left, or the wear sensor has triggered, replace all the pads on the axle.
Stage 2 of 4 Removal 5 steps
- Remove the two caliper guide bolts with a 14 mm socket. If the pin turns, hold it with a 17 mm wrench.
- Remove the caliper and hang it from the suspension spring or with a wire so that the brake hose is not stretched. Do not disconnect the hose.
- Take the pads and spring clips out of the bracket, and note the position of the pad with the wear sensor (if fitted).
- Remove the two caliper bracket bolts with a 14 mm socket and take off the bracket. Do not use impact tools for this.
- Remove the disc retaining screws (if present) with a Phillips screwdriver and take off the disc. If the disc is stuck, tap it carefully with a hammer on the hub area, not on the friction surface.
Stage 3 of 4 Installing the new parts 7 steps
- Clean the hub mounting surface with a wire brush to remove rust, then apply a very thin layer of anti-seize grease.
- Degrease the new disc with brake cleaner (the protective oil coating must be washed off), place it on the hub, align the holes, and install the screws.
- Clean the bracket, the pad seats, and the pins. Install the new spring clips. Lubricate the pins with a thin layer of suitable grease. Do not use copper grease on the pins.
- Install the bracket and tighten its bolts to about 55-60 N·m (41-44 lb-ft) (check the exact value in the Hyundai specifications).
- Insert the new pads: the pad with the wear sensor goes on the inner side. Apply a thin layer of grease to the contact surfaces of the pad backing plates, keeping it off the friction material.
- Retract the caliper piston. On a caliper with EPB, the piston is wound back by rotating it with a special tool rather than simply compressing it, and only after the caliper has been put into service mode. Do this slowly so you do not tear the dust boot.
- Fit the caliper over the bracket and tighten the guide bolts to about 28-32 N·m (21-24 lb-ft) (check the exact value in the specifications).
Stage 4 of 4 Finishing up and checking 6 steps
- Install the wheel and hand-tighten the lug nuts in a crisscross pattern. Lower the vehicle and tighten the nuts in a crisscross pattern to about 107-127 N·m (79-94 lb-ft) (check the exact value in the specifications).
- Repeat the procedure on the other side.
- Take the EPB out of service mode (using the factory procedure or a scan tool) so that the actuators return to normal operation and bring the pads up to the disc.
- Press the brake pedal several times until it feels firm. Check the brake fluid level in the reservoir and top it up to the proper level if necessary.
- Test the parking brake several times: apply and release it with the EPB switch, and make sure no warning lights come on in the instrument cluster.
- Take a test drive and bed in the new pads and discs: at least 200 km of gentle braking without hard stops.
Common mistakes and warnings
- Brakes are a safety system
- If you have no experience working on brake systems and electric parking brakes, leave the job to a repair shop
- Do not use an impact wrench on the caliper and disc fasteners
- Do not press the brake pedal while the caliper is removed
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Hyundai
Hyundai Motor Company, whose name means "modernity" in Korean, is South Korea's largest automaker and one of the top…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →