← C-class Mercedes-Benz C-class repair manuals →

Mercedes-Benz C-Class (W203) 2006: Front Brake Rotor Replacement

Replace the front rotors on the W203 as a pair, usually together with the pads, so the brakes work evenly. To do this, remove the caliper together with its bracket, take off the old rotor, and install the new one on a cleaned hub. This guide covers the front axle only; the rear axle is different (it has an integrated parking brake).

DifficultyMedium Time1.5-2.5 hours Steps26

Key figures

  • Caliper bracket bolt torquethe two most heavily loaded bolts, 18 mm socket, torque wrench mandatory (step 16)
    115 N·m (85 lb-ft)
  • Caliper guide pin torquetorque when installing the caliper on the bracket (step 19)
    25 N·m (18 lb-ft)
  • Wheel bolt torquetighten in a crisscross pattern after lowering the vehicle, recheck after 50-100 km (step 22)
    110 N·m (81 lb-ft)
  • ABS sensor mount torquewhen securing the sensor wire to the bracket (step 20)
    25 N·m (18 lb-ft)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

5
№PartAlternatives
01 Front ventilated brake rotors2 pcs, always as a pairFind on Amazon → AlternativesBremboATEZimmermannFebiTRW
02 Front brake pads (axle set)replaced together with the rotorsFind on Amazon →
03 Pad wear sensorif equippedFind on Amazon →
04 Brake grease for guide pinsFind on Amazon →
05 Brake cleanerFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

11
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 12 more. See manuals →

Step by step

26 steps · 5 stages
Stage 1 of 5 Preparation 4 steps
  1. Park the vehicle on level ground, put it in first gear or P, and place wheel chocks behind the rear wheels.
  2. Loosen the wheel bolts a quarter turn while the wheel is still on the ground.
  3. Open the hood and remove the brake fluid reservoir cap. When you push the pistons back, the fluid level will rise; if necessary, remove the excess fluid with a syringe.
  4. Raise the front of the vehicle, place it on jack stands, and remove the wheels.
Stage 2 of 5 Caliper and rotor removal 7 steps
  1. Inspect the hose, boots, and guide pins. If the hose is cracked or a boot is torn, replace the part.
  2. Disconnect the pad wear sensor connector (if installed) and move the wire aside.
  3. Remove the two caliper guide pins (installation torque: 25 N·m (18 lb-ft)) and lift the caliper off the bracket. Hang the caliper from the spring using wire or a hook. The brake hose must not carry the weight of the caliper.
  4. Remove the pads from the bracket and note their positions.
  5. If necessary, move the ABS sensor wire away from the bracket. The sensor mount is tightened to 25 N·m (18 lb-ft).
  6. Using an 18 mm socket, remove the two bolts that secure the caliper bracket to the steering knuckle and remove the bracket.
  7. Remove the rotor retaining screw (Torx T30), if present. Remove the rotor. If it is stuck: apply penetrating oil around the center of the hub and tap the rotor from the back with a rubber mallet.
Stage 3 of 5 Preparing the mounting surfaces 3 steps
  1. Clean the hub mounting surface of rust and dirt with a wire brush. Any unevenness will cause rotor runout and steering wheel vibration during braking.
  2. Clean the bracket and the pad seating areas. Apply a thin layer of grease to the guide pins and the pad sliding surfaces. Do not apply grease to the rotor or hub surfaces.
  3. Wipe the new rotors with brake cleaner to remove the protective oil coating. Do not touch the friction surfaces with your hands.
Stage 4 of 5 Installation 7 steps
  1. Place the new rotor on the hub and secure it with the screw (Torx T30). The torque is approximately 9-10 N·m (7-7.4 lb-ft) (use the exact value specified by the manufacturer).
  2. Install the caliper bracket and tighten the two bracket bolts to 115 N·m (85 lb-ft). These are the most critical fasteners, so a torque wrench is mandatory.
  3. Push the caliper piston all the way back with a C-clamp or piston spreader, using the old pad as a backing plate if necessary. Watch the fluid level in the reservoir.
  4. Install the new pads in the bracket and connect the wear sensor (if equipped).
  5. Place the caliper over the bracket and tighten the guide pins to 25 N·m (18 lb-ft).
  6. Secure the ABS sensor wire; the mounting torque is 25 N·m (18 lb-ft).
  7. Repeat all the steps on the other side.
Stage 5 of 5 Reassembly and check 5 steps
  1. Install the wheels, lower the vehicle, and tighten the wheel bolts in a crisscross pattern to 110 N·m (81 lb-ft).
  2. With the engine off, pump the brake pedal several times until it feels firm and the pads are seated against the rotors.
  3. Check the brake fluid level in the reservoir, top it up to the MAX mark if necessary, and close the cap.
  4. Test on a short stretch of road: the pedal should not sink, and there should be no pulsation or unusual noise.
  5. For the first 200-300 km, brake gently and avoid hard stops while the rotors and pads bed in. After 50-100 km, recheck the wheel bolt torque (110 N·m (81 lb-ft)).

Common mistakes and warnings

  • Brakes are a safety system
  • If you have no experience working on brake systems, have the repair done at a repair shop
  • Do not drive the vehicle until you are sure the brake pedal is firm
  • Keep brake fluid off the paint: it will damage it
  • Replace rotors and pads only as a full axle set
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →