Autopapyrus · Mercedes-Benz C-Class W203 2.0 CDI 122 hp (2006)
https://autopapyrus.com/catalog/mercedes-benz/c-class/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/mercedes-benz/c-class/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Mercedes-Benz C-Class W203 2.0 CDI 122 hp (2006): Engine Oil and Oil Filter Change
On the OM646 engine, the filter is a cartridge inside a plastic housing cap on top of the engine, so the only thing you need to undo from underneath is the drain plug. Change the oil at the interval given in the service book (usually every 10,000-15,000 km, or once a year if you mostly make short trips). This guide covers the 4-cylinder 2.0 CDI diesel.
Key figures
- Drain plug socket size13 mm, the "13 mm wrench" for step 7, and you will need it again when tightening in step 14
- Engine undershield6 screws, 8 mm socket, steps 5 and 15, and it must be removed to reach the plug
- Draining timeat least 10-15 minutes, step 7, otherwise old oil stays in the engine
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the engine shield, screws and drain plug are
Tap to enlarge
- 1Engine shield: ribbed plastic undertray. Remove it to reach the plug.
- 26 shield screws: undo with an 8 mm socket and remove the shield. Refit and tighten moderately.
- 3Drain plug: hex head with flange and copper washer, low on the right of the pan. Undo with a 13 mm socket, drain 10-15 minutes.
- 4Aluminium oil pan under the shield: the plug threads into it, stripping the thread is costly.
- 5Right-side wheel: a landmark showing which side to look.
Parts
4| № | Part | Alternatives |
|---|---|---|
| 01 | Diesel engine oil, MB 229.x approvalabout 6.5 L (6.9 qt) (some sources list 7.5 L (7.9 qt), low-ash for versions with a diesel particulate filterFind on Amazon → | |
| 02 | Oil filter element (cartridge) for OM646 with three housing O-ringsFind on Amazon → | AlternativesMannMahleBosch |
| 03 | Oil pan drain plugFind on Amazon → | |
| 04 | Copper drain plug sealing washerFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
10- 13 mm socket (drain plug) Amazon →
- 8 mm socket (engine undershield) Amazon →
- 14-point cup-type socket for the filter housing cap Amazon →
- ratchet Amazon →
- torque wrench Amazon →
- drain pan of 8 L (8.5 qt) or larger Amazon →
- funnel Amazon →
- jack and 2 jack stands (or a pit) Amazon →
- rags Amazon →
- thin flat screwdriver Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 12 more.
See manuals →
Step by step
20 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Warm up the engine for 15-20 minutes so the oil thins out. The oil will be hot, so wear gloves.
- Open the hood (release lever under the dashboard, then the black latch at the front).
- Turn the oil filler cap a quarter turn and remove it. Pull up and remove the decorative engine cover. Rest the filler cap on the filler neck without screwing it on, so the oil drains faster.
- Raise the front of the car: place the jack at the front right jacking point, then set the jack stands. Never work under a car supported only by a jack. Place wheel chocks behind the rear wheels.
Stage 2 of 5 Removal and draining 4 steps
- Remove the 6 engine undershield screws with an 8 mm socket and take off the undershield.
- Place the drain pan under the engine. The drain plug is at the bottom right.
- Remove the drain plug with a 13 mm socket and let the oil drain for at least 10-15 minutes.
- While the oil drains, use the 14-point socket to unscrew the oil filter housing cap on top of the engine. Lift out the housing together with the cartridge. It will still contain oil, so hold it over the pan or a rag.
Stage 3 of 5 Filter replacement 4 steps
- Remove the old cartridge from the housing. Use a thin screwdriver to carefully pry off the three old housing O-rings, without scratching the seating surfaces.
- Wipe the housing and the seating area in the engine block with a clean rag.
- Lubricate the new O-rings with clean engine oil and fit all three onto the housing, then install the new cartridge.
- Thread the housing with the filter into the block by hand until it stops, then tighten it with the 14-point socket and a torque wrench. The approximate torque is 20-25 N·m (15-18 lb-ft) (check the exact value against the manufacturer's specification). The housing is plastic, so do not overtighten.
Stage 4 of 5 Reassembly and refilling 4 steps
- Clean the drain plug and its seating surface, and install a new copper washer (it is better to replace the plug itself as well).
- Thread the plug in by hand, then tighten it with a torque wrench. The approximate torque is 25-30 N·m (18-22 lb-ft) (check the exact value against the manufacturer's specification). The plug threads into an aluminum oil pan, and stripped threads are expensive to repair.
- Refit the engine undershield with its 6 screws using the 8 mm socket (tighten them moderately, without excessive force), then lower the car onto level ground.
- Using the funnel, add about 6 L (6.3 qt) of oil, wait a couple of minutes, then top up in small amounts. Refit the decorative cover and the filler cap.
Stage 5 of 5 Check 4 steps
- Start the engine and run it for 1 minute. Make sure the oil pressure light goes out, and check the drain plug and filter cap for leaks.
- Shut off the engine, wait 5 minutes, then check the level on level ground. It should be between the min and max marks. Top up if necessary.
- Reset the service indicator: turn the ignition to position 2, select the service indicator in the instrument cluster menu, hold the reset button until you hear a signal, then hold it for about 3 more seconds until the reset confirmation appears.
- Take the used oil and old filter to a recycling center for disposal.
Common mistakes and warnings
- Work only on jack stands or over a pit; the car's factory jack is not suitable for this job
- Do not use oil without an MB approval for your engine version (especially if the car has a diesel particulate filter, which requires low-ash oil), or the particulate filter and engine will wear out early
- Do not overfill the oil above the max mark