← Tucson Hyundai Tucson repair manuals →

Hyundai Tucson (3rd generation, TL): Turn Signal Relay Diagnosis and Replacement

Older Hyundai models (for example, a 2005 Elantra) have a removable turn signal relay, which is often confused with the newer-generation electronics. On the Tucson TL (2015-2018), an electronic module produces the flashing, and there is no separate relay to replace. Symptoms: turn signals don't flash, flash too fast, or don't work at all. Most often the cause is a burned-out bulb, a blown fuse, a poor connector contact, or the turn signal switch on the steering column. Replace the module last.

DifficultyMedium Time30-60 minutes Steps8

Parts

3
№PartGenuine part no.
01 Turn signal / hazard circuit fuseFind on Amazon →
02 Turn signal bulb PY21W, amberFind on Amazon →
03 Interior fuse and relay box (complete)if faulty, special order onlyFind on Amazon → 91940-G3040
91940-G3050

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

4

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more. See manuals →

Step by step

8 steps
  1. Check the flash rate. If it is twice as fast as normal, a bulb on one side has almost certainly burned out (front, rear, or side repeater). This is the module's normal response to a broken load. Replace the faulty bulb.
  2. If neither direction works and the hazard lights are dead too, open the interior fuse box cover (under the dash on the driver's left). The diagram is printed on the inside of the cover. Find the hazard / turn signal circuit fuse, pull it out with a fuse puller, and inspect the element. Replace it with a fuse of the same rating.
  3. If the fuse is good, turn the ignition on and test the hazard lights separately from the turn signals. If the hazards work but the turn signals don't, suspect the turn signal switch on the steering column. If nothing works, suspect the module or its power supply.
  4. To check the switch, remove the lower steering column cover (usually held by clips and 2-3 screws) and carefully disconnect the turn signal switch connector. Inspect the contacts for corrosion and breakage, and test continuity with a multimeter with the lever engaged.
  5. Inspect the fuse and relay box connectors for corrosion, burning, and loose terminals. Clean the contacts with electrical contact cleaner.
  6. If none of these checks help, the body control module (BCM / fuse and relay box) must be replaced or repaired. First disconnect the negative battery terminal and wait 5-10 minutes. Remove the lower trim panel on the left, disconnect the module connectors, and install a new module.
  7. After replacing the module, reconnect the battery and check the turn signals, hazard lights, parking lights, and brake lights. Some modules require coding or pairing to the vehicle, so it is better to have a complete module replacement done at a repair shop with diagnostic equipment.
  8. If the flashing is erratic after installing LED bulbs, the cause is low load. Go back to the stock bulbs or install load resistors.

Common mistakes and warnings

  • Before any work on the fuse box and connectors, disconnect the negative battery terminal
  • Do not install a fuse with a higher rating: this risks melting the wiring
  • Check the fuse locations and functions for your trim level against the diagram on the box cover
  • If replacing the module requires coding, take the car to a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →