← Tucson Hyundai Tucson repair manuals →

Hyundai Tucson (TL, 2018): Cabin Air Filter Replacement

The Tucson TL cabin air filter sits behind the glove box, on the passenger side. You don't need to remove the whole glove box: just disconnect the stops and lower it down. Follow the maintenance schedule in your owner's manual for the replacement interval. If the filter is dark gray and clogged, airflow is weak, or there is an odor from the vents, replace it sooner.

DifficultyEasy Time10-15 minutes Steps19 ToolsNone needed (everything comes off by hand)

Diagram: where the filter is and how to get to it

The view from the passenger seat with the glovebox lowered dashboard dashboard heater blower filter cover glovebox lowered to the floor mat arrow pointing down towards the floor mat 1 damper rod 2 stops 4 tabs 5 3 Tap to enlarge
  1. 1glovebox damper rod on the right: pull it off its plastic pin
  2. 2two stops on the sides of the glovebox: lift the glovebox slightly, turn each a quarter turn anticlockwise and pull it out
  3. 3glovebox: it then drops down by itself, no need to remove it
  4. 4filter cover: squeeze the two tabs on the left, pull the left edge towards you and slide the cover left
  5. 5filter: pull it straight out. Fit the new one with the arrow pointing down, towards the floor mat

Part

№PartAlternatives
01 Cabin air filter for Hyundai Tucson TL, rectangular, with "Air Flow" direction arrowoptional carbon-layer versionFind on Amazon → AlternativesMannBoschTYCDoowon

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more. See manuals →

Step by step

19 steps · 4 stages
Stage 1 of 4 Accessing the filter 5 steps
  1. Turn off the engine, open the glove box, and empty it completely.
  2. On the right side of the glove box, pull the black plastic damper arm off its two-prong pin.
  3. Inside the glove box, find the two round black stops on the sides. Lift the glove box about 2-3 cm to take the load off the stops.
  4. Turn each stop a quarter turn counterclockwise and pull it straight toward you. Set both aside.
  5. Carefully lower the glove box down to the floor mat. This exposes the black heater blower housing and the rectangular filter cover.
Stage 2 of 4 Removing the old filter 6 steps
  1. Squeeze the two tabs on the left side of the cover to release the latch.
  2. Pull the left side of the cover toward you.
  3. Slide the cover to the left so the right tab comes out of the slot in the housing, then remove it.
  4. Pull the old filter straight out. Note which way the arrow was pointing.
  5. Inspect the filter. If it is dark gray or black and clogged, replace it. Replace it in any case if there is an odor or weak airflow.
  6. Optionally, vacuum the filter compartment with a narrow nozzle to remove leaves and debris.
Stage 3 of 4 Installation and reassembly 6 steps
  1. Orient the new filter with the "Air Flow" arrow (↓) pointing down, toward the floor mat. Wrong orientation causes noise and reduces filtration.
  2. Insert the filter straight in until it stops, flush with the opening.
  3. Install the cover: first the right tab into the slot in the housing, then press the left side until the latch clicks. Check that the cover sits tight.
  4. Lift the glove box up toward the dashboard so the holes for the stops line up.
  5. Insert both stops and turn each a quarter turn clockwise until it locks.
  6. Put the damper arm back on the pin on the right and make sure it sits securely.
Stage 4 of 4 Check 2 steps
  1. Put your items back in the glove box and close it. It should move smoothly, without knocking.
  2. Turn the ignition on and set the fan to maximum: air should flow evenly, without whistling or unusual noise. If it is noisy, check the arrow orientation and how the cover is seated.

Common mistakes and warnings

  • Don't force the glove box down: first disconnect the damper arm and the stops, otherwise you can break the plastic tabs
  • No tightening torques are needed, since all the fasteners are quarter-turn locks and clips
Spotted a mistake? Tell us →

Our articles

More articles →