Autopapyrus · Kia Rio 1.6 MPI (2021)
https://autopapyrus.com/catalog/kia/rio/guides/exhaust-system-replacement-from-the-catalytic-converter-to-the-rear-muffler/
https://autopapyrus.com/catalog/kia/rio/guides/exhaust-system-replacement-from-the-catalytic-converter-to-the-rear-muffler/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Kia Rio 1.6 MPI (2021): Exhaust System Replacement from the Catalytic Converter to the Rear Muffler
The Kia Rio 1.6 MPI exhaust system consists of a front section with a catalytic converter, a center section with a resonator, and a rear muffler. They are connected by flanges with gaskets and attached to the body with rubber hangers. The system is easier to replace on a cold engine, after treating the threads with penetrating oil in advance. It is best to replace the hangers at the same time.
Diagram: where the flex joint, catalytic converter, flanges and hangers are on the removed exhaust
Tap to enlarge
- 1Flex joint near the engine: do not bend it when lowering the pipe, it tears
- 2Front section with the catalytic converter: heavy, the ceramic inside is fragile, do not hit or drop it
- 3Oxygen sensor wire: disconnect the connector and free the wire from the holders first
- 4Flange with gasket: the nuts rust badly, soak them in penetrating oil first, fit new gaskets on assembly
- 5Middle section with the resonator: pull it out with the rear muffler if they are one unit
- 6Rubber hanger: pry off with a pry bar or slide off with a puller, fit new ones on assembly
- 7Rear muffler: removed first while holding the system by hand or on a stand
Parts
7| № | Part | Genuine part no. |
|---|---|---|
| 01 | Muffler flex pipe (flexible joint)Find on Amazon → | |
| 02 | Front pipe with catalytic converter for Kia Rio IV 1.6 MPI (G4FG)Find on Amazon → | 28610-H9200 |
| 03 | Center section (resonator) for Kia Rio IV 1.6 MPI (G4FG)Find on Amazon → | 28650-H9220 |
| 04 | Rear muffler for Kia Rio IV 1.6 MPI (G4FG)Find on Amazon → | 28710-H9100 |
| 28710-H9600 | ||
| 05 | Flange gasket set (multilayer metal)Find on Amazon → | |
| 06 | Flange nuts and boltsnewFind on Amazon → | |
| 07 | Rubber muffler hangersFind on Amazon → |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
8- lift or pit (or a jack and reliable jack stands) Amazon →
- sockets and wrenches (approximately 12-17 mm) Amazon →
- ratchet Amazon →
- torque wrench Amazon →
- penetrating oil (WD-40 or equivalent) Amazon →
- wire brush Amazon →
- pry bar or special rubber hanger removal tool Amazon →
- gloves and safety glasses Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 6 more.
See manuals →
Step by step
17 steps- Shut off the engine and let the exhaust system cool down completely, at least 1-2 hours. Secure the vehicle on a lift or on jack stands. Do not rely on a jack alone. Disconnecting the battery is optional, but be careful not to damage the wires and connectors of the oxygen sensors during removal.
- Generously apply penetrating oil to all flange nuts and bolts. Let it soak for 15-30 minutes, then apply it again. These nuts rust heavily, and on an older car they often seize.
- Remove the engine undercover and underbody shield if it covers the front section, along with the heat shields above the catalytic converter and above the pipe. The heat shield fasteners are thin, so do not force them. Heat shield tightening torques are low, approximately 8-12 N·m (6-9 lb-ft). Check the exact value against the manufacturer's specifications.
- Disconnect the oxygen sensor connectors (upstream and downstream of the catalytic converter). Carefully free the wires from their holders so they do not tear when the pipes are lowered.
- Mark or photograph the position of all flanges and hangers so you do not mix them up during reassembly.
- Support the rear of the system by hand or with a stand. Remove the rear muffler by prying the rubber hangers off with a pry bar or sliding them off with a special removal tool. Silicone-based lubricant will help if the rubber has stuck. Do not let the system drop on its hangers: the flex pipe tears when it is bent too far.
- Unbolt the flange between the center section and the front section. If the studs or bolts are seized, you may heat them only if you are completely sure there are no fuel or brake lines or plastic nearby. It is better to wait for the oil to penetrate or to cut them off with an angle grinder, and then replace the studs as well.
- Disconnect the front section with the catalytic converter from the exhaust manifold or from the adapter flange. Hold it with your hands: the catalytic converter is heavy, and the ceramic is fragile and is sensitive to impacts.
- Take the pipes out from under the vehicle. Remove the rear muffler and center section together if they come as a single assembly. Wiggle them slightly to work around the crossmembers and the fuel tank.
- Clean the mating surfaces of the flanges with a wire brush to remove carbon deposits and rust. You need a flat, clean surface, otherwise the gasket will not seal and a leak will appear.
- First compare the new parts with the old ones: length, flange positions, number and location of hangers, and the location of the oxygen sensors. Resolve any differences before installation.
- Install new gaskets and the front section with the catalytic converter. Tighten the nuts in a crisscross pattern and in stages, first by hand, then with a wrench, but do not fully tighten them yet. Reusing old nuts is not recommended, as they deform and rust.
- Attach the center section and rear muffler with new gaskets, fitting the new rubber hangers. Let the system settle into the correct position under the vehicle: the clearances to the body, floor, tank and suspension must be even, and nothing should touch the body.
- Do the final tightening of the flanges with a torque wrench, in a crisscross pattern, in 2-3 passes. The approximate torque for exhaust flange nuts is 30-50 N·m (22-37 lb-ft). Check the exact value against the manufacturer's specifications. Tighten the heat shields to a low torque, 8-12 N·m (6-9 lb-ft), and check the exact value against the manufacturer's specifications.
- Connect the oxygen sensor connectors and secure the wires in their holders. Install the underbody shield and heat shields.
- Start the engine and inspect all flanges for exhaust leaks. Hold your palm near the joints without touching hot parts, or listen for a hissing leak. If you notice noise or a smell, tighten the joint again.
- Take a test drive of 10-15 km (6-9 miles). Stop, let the system cool down, and retighten the flanges again. Gaskets settle after warming up. Then check that the system does not vibrate and does not touch the floor.
Common mistakes and warnings
- The exhaust system gets very hot, and burns are possible even an hour after the engine is shut off
- Do not heat seized nuts with a torch near fuel lines, brake lines and plastic parts
- Work only on reliable jack stands
- Do not get under a vehicle that is held up by a single jack
- The catalytic converter is fragile: do not drop it or hit it
- Do not allow exhaust leaks upstream of the oxygen sensors, as they will turn on the Check Engine light
- The tightening torques in this guide are approximate, so check the exact values against the manufacturer's specifications
- If you have no experience working under a vehicle, leave the job to a repair shop
Spotted a mistake? Tell us →
Our articles
Before you buy
What Car to Buy for 1.5 Million Roubles: New, Used and Five Questions Before You Pay
A new Haval Jolion costs from 2,099,000 roubles, not 1.45 million. We compared new car prices with the budget, looked…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →