← Rio Kia Rio repair manuals →

Kia Rio 1.6 MPI (2021): Fixing an Intake Air Leak

An intake air leak on the 1.6 MPI causes a fluctuating or high idle speed, a whistling noise from the intake, fuel mixture codes (P0171), and a misfire on a warm engine. First locate the leak, then replace only the faulty hoses or the manifold gasket.

DifficultyMedium Time1.5-3 hours Steps10

Diagram: where the intake manifold, gaskets and hose are when fixing an air leak

View of the intake manifold from the front and above1Intake manifold5Fuel rail with injectors2Gaskets and bolts4Filter hose3Throttle body6Air filterBelow: the cylinder head flange with four portsPlenum with coverTap to enlarge
  1. 1Intake manifold: black plastic plenum with four runners to the head. Check for cracks and a warped mating face; remove it to replace the gasket.
  2. 2Gaskets and bolts: each port has its own gasket and bolts. Replace the gaskets, tighten bolts from the centre outward in several passes, about 15-25 Nm per the manual.
  3. 3Throttle body: sits at the plenum inlet. Disconnect the cable or connector and tighten per the manual.
  4. 4Air filter corrugated hose: ribbed hose to the throttle. Check the bends for cracks, loosen the clamps and replace it if it leaks.
  5. 5Fuel rail with injectors: at the head flange. Remove only if it is in the way, after relieving pressure per the manual.
  6. 6Air filter housing: a landmark, removed together with the hose before taking off the manifold.

Parts

6
№PartGenuine part no.Alternatives
01 Intake manifold gasket, 1.6 MPI Gamma engineFind on Amazon → AlternativesMannBoschVictor Reinz
02 Corrugated air intake hoseif wornFind on Amazon → 28210-H9100 AlternativesMannBoschVictor Reinz
03 Throttle body hoseif wornFind on Amazon → 28210-H9100 AlternativesMannBoschVictor Reinz
04 Vacuum linesif wornFind on Amazon → AlternativesMannBoschVictor Reinz
05 Crankcase ventilation hoseif wornFind on Amazon → 26710-2B830 AlternativesMannBoschVictor Reinz
06 Hose clampsFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

7

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 6 more. See manuals →

Step by step

10 steps
  1. Let the engine cool down completely and disconnect the negative battery terminal. Remove the engine cover.
  2. Find the leak. With the engine idling, inspect the corrugated hose between the air filter and the throttle body for cracks and tears, and check the clamps, vacuum lines, and crankcase ventilation hose. Feed smoke into the intake or carefully spray the joints with cleaner: if the engine speed changes, you have found the leak. Use the cleaner carefully, away from open flames and the hot exhaust.
  3. If the corrugated hose or a duct is leaking: loosen the clamps, disconnect the mass airflow sensor connector and the ventilation hoses, and remove the hose. Inspect it while flexed and stretched, since cracks show up in the folds. Install the new one and tighten the clamps with moderate force, without overtightening.
  4. To replace the manifold gasket, remove the air filter with its housing and the corrugated hose. Disconnect the throttle cable or connector, the injector and sensor connectors on the manifold, the vacuum hoses, and the brake booster hose. Mark or photograph the position of all connectors and hoses.
  5. Relieve the pressure in the fuel rail if the rail is mounted on the manifold and has to be removed: follow the manufacturer's procedure for relieving fuel pressure. If the rail is not in the way, do not touch the injectors or fuel lines.
  6. Remove the manifold fasteners, loosening them in a crisscross pattern from the center outward, evenly, in several passes. Remove the manifold and cover the intake ports with a clean rag so nothing falls into the cylinders.
  7. Clean the mating surfaces of any old gasket material. Do not leave scratches, and do not let debris get into the ports. Inspect the manifold for cracks and for a warped mating surface.
  8. Install the new gasket, seat the manifold, and tighten the fasteners from the center outward in several passes. The approximate manifold fastener torque is 15-25 N·m (11-18 lb-ft); check the exact value against the manufacturer's specifications. Tighten the throttle body and other components to the manufacturer's specifications as well.
  9. Reconnect all connectors and hoses, install the air filter with its ducts, and reconnect the battery.
  10. Start the engine, let it run, and recheck for leaks (smoke or cleaner). If necessary, read and clear any codes with the scanner. After the battery has been replaced or disconnected, the idle speed may fluctuate for a while until the control unit relearns. Take a test drive.

Common mistakes and warnings

  • Work only on a cold engine with the battery disconnected, and do not let debris get into the intake ports
  • The exact procedure and torque values for this engine are approximate, so check them against the manufacturer's specifications
  • If you have no experience working on fuel systems, have a repair shop replace the gasket
Spotted a mistake? Tell us →

Our articles

More articles →