← Granta

Lada Granta 1.6 8V VAZ-11186 (2024): Valve Stem Seal Replacement

Replace the seals if blue smoke comes from the exhaust at idle, especially after the car has sat for a long time or when you lift off the throttle, and oil is left on the threads and electrodes of the spark plugs. First rule out a clogged crankcase ventilation system: with that problem, oil is pushed out of the engine, but there is no smoke. The job is done without removing the cylinder head, but it is labor-intensive and requires care. The exact procedure for removing components on this engine is only partly documented in public sources, so the torque values below are approximate. Check the exact values against the manufacturer's specifications.

DifficultyHard Time5-8 hoursincluding timing belt and valve lash adjustment Steps20

Diagram: where the spark plug holes, timing belt and negative terminal are when replacing valve stem seals

Engine as seen with the hood open, from the radiator sidemark on the pulleybatteryplus1Cylinder head, cover removed2Spark plug holes: 43Timing belt and cover4MinusTap to enlarge
  1. 1Cylinder head with the valve cover removed: the seals are replaced here, the head stays on.
  2. 2Spark plug holes, there are four: unscrew the plugs, then insert the aluminium stop through the holes.
  3. 3Timing belt and cover: remove the cover and align the marks on the pulley and crankshaft before taking the belt off.
  4. 4Battery: disconnect the negative terminal before starting work.

Parts

5
№PartAlternatives
01 Valve stem seal set, 8 valves (intake and exhaust)Find on Amazon → AlternativesVictor ReinzElringGoetze
02 Valve cover gasketFind on Amazon →
03 Timing belt with rollers (kit)best replaced if the pulley and belt were removedFind on Amazon → AlternativesGatesContitech
04 Engine oilif drainedFind on Amazon →
05 Coolantif drainedFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Step by step

20 steps
  1. Park the car on level ground, shut off the engine, and let it cool. Disconnect the negative battery terminal.
  2. Remove the air filter with its ducts, disconnect the connectors and hoses that block access to the valve cover, and remove the ignition coil (module). Remember or photograph the position of all hoses and wires.
  3. Remove all four spark plugs. They are fragile, so unscrew them strictly along the axis, without tilting. Inspect them: oil traces confirm the diagnosis.
  4. Remove the valve cover and the alternator drive belt. Remove the timing belt protective cover.
  5. Turn the crankshaft clockwise (by the pulley bolt, not by the camshaft gear) and align the timing marks. Check the position of the marks on the camshaft pulley and on the crankshaft so you can return everything to exactly the same position later.
  6. Loosen the tensioner and take the timing belt off the camshaft gear. It is best to replace the belt after removal, especially if it has already reached the end of its service life. Do not turn the crankshaft or camshaft while the belt is off, and after removing the belt, set the pistons as required by your chosen method of holding the valves.
  7. Remove the camshaft with its bearing caps, following the loosening order for the bolts (evenly, from the edges toward the center, in several passes). Lay out the tappets and adjusting shims strictly in order, labeled with the valve number. Mixed-up parts will throw off the valve clearances.
  8. Working one cylinder at a time, set the piston to top dead center (TDC). Through the spark plug hole, insert a slightly bent aluminum rod about 10 mm thick between the piston and the valve head so the valve does not drop into the cylinder. Do not use a screwdriver: it scratches the piston. Some mechanics instead feed compressed air through the spark plug hole. This is acceptable if you have a compressor and an adapter.
  9. Install the valve spring compressor, compress the valve spring, and remove the keepers with tweezers. Cover the area with a rag: a keeper can "shoot" out. Keep a couple of spare keepers on hand. If the retainer is stuck to the keepers, place a pipe or socket on it and tap it lightly with a hammer. Do not push on the lever with all your strength.
  10. Remove the upper retainer and the spring. Lay out the parts by valve, in order.
  11. Remove the old seal with a dedicated remover (impact type preferred). Do not use screwdrivers or pliers: the thin upper part of the valve guide is easily broken.
  12. Lubricate the new seal and the valve stem with clean engine oil. Slide the seal onto the stem through the protective plastic sleeve (if included in the kit) so the seal lip is not torn on the keeper groove.
  13. Seat the seal with a drift that rests only on its collar, without excessive force. A seal with torn rubber, or one that has turned barrel-shaped from being pressed too far, goes in the trash.
  14. Install the spring and retainer, compress them with the spring compressor, and fit the keepers. Make sure both keepers are seated in the groove, and tap the retainer lightly with a hammer through a drift.
  15. Repeat steps 8-14 for the remaining valves. Work one cylinder at a time.
  16. Install the tappets and shims in their original positions, fit the camshaft with its bearing caps, and tighten the fasteners in the correct order with a torque wrench (torque per the manufacturer's specification). Install a new camshaft seal at the same time.
  17. Install the timing belt with the marks aligned, adjust the tension per the specification, turn the crankshaft two full revolutions twice, and recheck the marks. Install the covers.
  18. Check and, if necessary, adjust the valve lash with a feeler gauge (values per the VAZ specification), because the shims and tappets were removed.
  19. Install the valve cover with a new gasket and tighten the bolts evenly in a crisscross pattern to a low torque (usually a few N·m, with the exact value per the specification). Install the spark plugs and tighten them with a torque wrench per the specification.
  20. Install the ignition coil and the air filter, and reconnect the battery. Start the engine and check for oil leaks and unusual noises. For the first 200-300 km (125-185 miles), drive without heavy loads, then check the oil level.

Common mistakes and warnings

  • A mistake when installing the timing belt or seating the tappets can cause the pistons to hit the valves and lead to serious engine repairs
  • If you have no experience with a valve spring compressor and timing marks, leave the job to a repair shop
  • Choose seals from well-known manufacturers rather than the cheapest ones
  • If the upper part of a valve guide is broken during removal, you will need a repair bushing or a more extensive repair
Spotted a mistake? Tell us →