← Vesta

Lada Vesta 1.6 16v VAZ-21129 (2018): Valve Stem Seal Replacement

On the VAZ-21129, valve stem seals can be replaced without removing the cylinder head: first the timing belt, valve cover and camshafts are removed, and the valves are held up by compressed air through the spark plug hole. Signs of wear: blue smoke at startup and on throttle lift-off, oil consumption, oily spark plugs. The job is long and requires precision: if the keepers (collets) are installed incorrectly, the valve will drop into the cylinder.

DifficultyHard Time6-10 hours Steps32

Key figures

  • Air pressure to hold the valves
    at least 2 bar. It is supplied by a compressor through the spark plug hole so the valves do not drop (step 13)
  • Crankshaft rotation between cylinder pairs
    180°. After replacing the seals on cylinders 1 and 4, turn the crankshaft and move on to cylinders 2 and 3 (step 21)
  • Camshaft bearing housing bolts
    20 pcs, 8 mm socket. This is how many bolts must be loosened and tightened in a crisscross pattern (steps 11 and 24)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the tappets, valves and 20 bolts are on the cylinder head

This is how the cylinder head looks from above: camshafts removedWhat is under the tappet (cross-section)tappetcottersplatespringsealguide1Tappet2Valve under the tappet3Spark plug well420 housing boltsall 20 are circled5Pulley and timing beltTap to enlarge
  1. 1Tappet: sits in a narrow well of the head. Remove one by one and keep them in order in clean oil so they return to the same place.
  2. 2Valve under the tappet: spring with a plate, two cotters and an oil seal on the guide. Compress the spring with a valve spring compressor, remove the cotters and replace the seal.
  3. 3Spark plug well: screw in the adapter and supply air of at least 2 bar so the valves do not drop.
  4. 420 camshaft bearing housing bolts (8 mm socket): loosen evenly from the edges to the center, tighten crosswise from the center to the edges.
  5. 5Camshaft pulley and timing belt under the cover on the left: do not turn the crankshaft or camshafts with the belt removed.

Parts

7
№PartAlternatives
01 Valve stem seal set, 16 valves (intake and exhaust)16 pcsFind on Amazon → AlternativesElringGoetzePayen
02 Valve cover gasketFind on Amazon →
03 Spark plug well sealsFind on Amazon →
04 Camshaft oil sealsFind on Amazon →
05 Timing belt with rollersrecommended to replace at the same timeFind on Amazon →
06 Engine oilfor topping upFind on Amazon →
07 Coolantfor topping upFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Step by step

32 steps · 5 stages
Stage 1 of 5 Preparation 5 steps
  1. Warm up the engine before cleaning, then let it cool. Park the car on a level surface, put the shifter in neutral, and chock the wheels.
  2. Disconnect the negative battery terminal.
  3. Remove the decorative engine cover and the air duct with the air filter housing to gain access to the valve cover.
  4. Remove the ignition coils and unscrew all 4 spark plugs. Blow out the spark plug wells with compressed air before unscrewing.
  5. Drain the coolant if you plan to replace the water pump along with the timing belt (optional).
Stage 2 of 5 Removing the timing drive and camshafts 7 steps
  1. Remove the accessory drive belt and the timing belt covers.
  2. Set the piston of cylinder 1 to TDC on the compression stroke using the marks on the pulleys and the cover, and lock the crankshaft.
  3. Loosen the timing belt tensioner and remove the timing belt. Do not turn the camshafts or the crankshaft with the belt removed.
  4. Remove the camshaft pulleys, then the rear timing belt cover.
  5. Remove the valve cover fasteners and take the cover off, then clean the oil deflector.
  6. Evenly loosen the 20 camshaft bearing housing bolts (8 mm socket) working from the edges toward the center, remove the housing, then both camshafts. Remove the hydraulic lifters one at a time and place them in order in a container of clean oil so they return to their original positions.
  7. Use a syringe or bulb to remove any remaining oil from the wells, and cover the lifter bores with a ring cut from a plastic bottle or with a cloth so they don't get scratched.
Stage 3 of 5 Replacing the seals 9 steps
  1. Screw the adapter into the spark plug hole of the cylinder whose piston is at TDC and apply air (at least 2 bar). The air keeps the valves from dropping.
  2. Install the valve spring compressor bracket on the head (a camshaft bearing housing bolt works well). Place the stop on the spring retainer and the hook under the bolt head, taking care not to touch the walls of the lifter bore.
  3. Compress the spring and remove the two keepers with tweezers or a magnetic screwdriver. If the retainer is stuck, tap the tool lightly.
  4. Slowly release the spring, then remove the compressor, the retainer and the spring.
  5. Use the seal remover (or pliers) to pull the old seal off the valve guide straight up, without tilting it.
  6. Lubricate the valve stem and the working lip of the new seal with clean engine oil. Fit the plastic installation sleeve from the kit onto the stem so the seal is not cut by the keeper grooves.
  7. Slide the seal over the sleeve, remove the sleeve, and use the drift with light hammer taps to seat the seal fully onto the guide.
  8. Install the spring and retainer, compress the spring and insert both keepers into the stem grooves. Tap lightly on the end of the stem to make sure the keepers are seated. A poorly seated keeper will cause the valve to drop.
  9. Repeat for the remaining valves of cylinders 1 and 4 (pistons at TDC). Then turn the crankshaft 180° and replace the seals of cylinders 2 and 3. Each time, apply air to the corresponding cylinder.
Stage 4 of 5 Reassembly 8 steps
  1. Install the hydraulic lifters in their original positions, and lubricate the lifters, the bearing supports and the camshaft journals with clean oil.
  2. Lay in the camshafts (do not mix up the intake and exhaust), with the cylinder 1 cam lobes pointing away from the lifters.
  3. Apply a thin layer of sealant to the head surface under the bearing housing and check the locating dowels. Install the housing and tighten the bolts in a crisscross pattern, from the center outward, to the manufacturer's specification (approximately 8-12 N·m (6-9 lb-ft); verify the exact value against the service manual). After applying sealant, wait at least 1 hour before starting the engine.
  4. Replace the camshaft oil seals, install the valve cover with a new gasket, and tighten the bolts to specification (approximately 6-10 N·m (4-7 lb-ft)).
  5. Install the rear cover and the camshaft pulleys (bolts to the manufacturer's specification), and set the timing marks to the TDC position.
  6. Install the new timing belt and rollers, tension the belt according to the service manual marks, turn the crankshaft two full revolutions by hand and recheck the marks.
  7. Install the covers, the accessory drive belt, the ignition coils and the spark plugs. Tighten the spark plugs to 25-30 N·m (18-22 lb-ft) (verify against the service manual).
  8. Connect the battery, reinstall the air filter housing and the decorative cover, and if needed refill the coolant and bleed the air from the cooling system.
Stage 5 of 5 Checking 3 steps
  1. Check the oil level and top up if necessary.
  2. Start the engine and let it idle. Make sure there are no leaks around the valve cover and no oil drips under the car. The hydraulic lifters may tick for a couple of minutes until they fill with oil.
  3. Take a test drive of 10-20 km (6-12 miles), then check the oil level and look for leaks again. Smoke at startup and oil consumption should be gone.

Common mistakes and warnings

  • The main hazards are a dropped valve or incorrect timing marks: on the 21129, if the timing is out of phase, the valves may hit the pistons
  • Do not turn the crankshaft with the belt removed, and watch the keepers when working with the valve spring compressor
  • If you have no experience with timing drives and valve spring removal, leave the job to a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →