← Range Rover Sport Land Rover Range Rover Sport repair manuals →

Land Rover Range Rover Sport (2016, L494): Bleeding Air from the Cooling and Heater System

Air in the cooling system most often appears after replacing coolant, hoses, or a radiator. Symptoms: the heater blows cold air, or warm air only at higher rpm; gurgling behind the dashboard; the lower heater hose is cold while the engine is hot. The best way to remove air is a vacuum refill. The backup method is warming up the engine with the bleed screws open. Bleed screw locations depend on the engine (V6 diesel, supercharged V6 gasoline, V8), so look for them on the upper hoses, on the connecting pipe at the front of the engine, and near the expansion tank.

DifficultyMedium Time1-2 hours Steps18

Parts

2
№Part
01 Coolant (antifreeze)for topping offFind on Amazon →
02 Cooling system bleed screws (plugs)if the old ones are worn or brokenFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

18 steps · 4 stages
Stage 1 of 4 Preparation 4 steps
  1. Park the vehicle on level ground, or preferably with the front slightly higher (on an incline or on jack stands, securely supported). This lets air move toward the high points of the system. The engine must be cold.
  2. Open the hood. Locate the expansion tank, the bleed screws, and the upper hoses. Wipe these areas clean so you can spot any leaks.
  3. Inspect the hoses and connections for leaks and coolant residue. If air keeps coming back, the cause may be a leak rather than the air pocket itself.
  4. Check the level in the expansion tank with the engine cold. If it is below the mark, top off with coolant to the "cold" level.
Stage 2 of 4 Vacuum refill (preferred method) 4 steps
  1. Drain the coolant if the system is badly depleted or there is a lot of air. Dispose of it properly, as it is toxic.
  2. Connect the vacuum kit to the expansion tank filler neck following the kit's instructions. Pull a vacuum and confirm that it holds. If it drops, look for a leaking connection.
  3. Without releasing the vacuum, open the supply of new coolant. The system will fill without air pockets. Fill to the "cold" mark.
  4. Remove the equipment and close the expansion tank cap.
Stage 3 of 4 Warm-up and air removal (if you don't have a vacuum kit or an air pocket remains) 6 steps
  1. Pour coolant in through the expansion tank and through the upper filling point, if it is open. Then open the bleed screws 1-2 turns. Loosen them carefully: old screws are brittle and easy to break, and then hot coolant sprays out in a jet.
  2. Set the cabin temperature to maximum, turn on the heater, and set the fan to medium speed. If the vehicle has separate rear climate control, turn on the rear circuit as well.
  3. Start the engine. Hold the engine speed at about 2000-2500 rpm. Watch the level in the expansion tank and top it off as needed.
  4. Once the thermostat opens and the engine warms up, coolant with bubbles will come out of the bleed screws. Close each screw when clean coolant without bubbles comes out. Close it carefully, with a light tightening and without much force. Check the tightening torque in the manufacturer's service manual.
  5. If you can't shut the engine off right away, keep warming it up until both heater hoses at the firewall are hot. If the lower hose is cold, air remains. Open the nearest bleed screw and release the air pocket.
  6. Shut off the engine. Let it cool down. Open the expansion tank cap only when the engine is cold.
Stage 4 of 4 Check 4 steps
  1. Top off the coolant to the "cold" mark. Close the cap until it clicks.
  2. Take a 10-15 minute test drive. The heater should warm up both at idle and at higher rpm. Make sure the temperature gauge stays steady.
  3. After the engine cools down, check the level again. If it has dropped, air is still working its way out. Repeat the warm-up and bleeding.
  4. If the heater is still cold while the engine is hot, possible causes are: remaining air in the heater core, a faulty valve or pump in the heater circuit, a clogged heater core, or a leaking hose. To purge additional air, start the engine, turn on the ignition, and cycle the fan and the temperature control.

Common mistakes and warnings

  • Do not open the expansion tank cap or the bleed screws on a hot engine
  • A jet of hot coolant causes burns
  • Coolant is poisonous: clean up any spills and keep it out of reach of children and pets
  • Do not drive with an overheated engine: if the temperature rises, stop immediately and shut off the engine
  • Check the approximate values (engine speed, screw tightening torque) in the manufacturer's service manual
Spotted a mistake? Tell us →

Our articles

More articles →