Autopapyrus · Lexus LX 4.5 V8 diesel 1VD-FTV (2017)
https://autopapyrus.com/catalog/lexus/lx/guides/cylinder-compression-test/
https://autopapyrus.com/catalog/lexus/lx/guides/cylinder-compression-test/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lexus LX 4.5 V8 diesel 1VD-FTV (2017): Compression pressure test
The 1VD-FTV engine (V8, 4461 cc, compression ratio 16.8) is checked by measuring the end-of-compression pressure in each of the 8 cylinders. The test is done through the glow plug hole (easier) or the injector hole while the engine is cranked by the starter with fuel delivery disabled. This guide covers the test through the glow plug hole. Take the reference spec from the Toyota service manual for this engine: only a rough guideline is given below.
Key figures
- Starter cranking speed during the testcheck before starting work (steps 1 and 13), otherwise a weak battery will give low readings200-250 rpm
- Test adapter threadadapter size for the glow plug hole or injector simulator (steps 10 and 15)M10 x 1.25
- Engine compression ratioa reference figure for the 1VD-FTV engine, not the pressure the gauge will show16.8
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: what a glow plug looks like and where to hold it during the compression test
Tap to enlarge
- 1Whole glow plug: grey metal body, rusty in places. Remove it only in the cylinder being tested, keep the wrench exactly on the axis.
- 2Thin part of the plug that goes into the cylinder. Do not tilt the wrench: the plug is thin and can break.
- 3Long coarse thread, wider than the body: screwed into the cylinder head. If it is stiff, soak it with penetrating oil and wait. Apply heat-resistant grease before installing.
- 4Hex next to the terminal: the glow plug socket goes on it. Tighten to the specified torque when installing.
- 5Terminal stud with a washer: the power connector or bus bar attaches here. Disconnect it before unscrewing.
Parts
4| № | Part |
|---|---|
| 01 | Glow plug or injector seal and washer setFind on Amazon → |
| 02 | Copper or steel injector sealing washerswhen removing injectorsFind on Amazon → |
| 03 | Injector fasteners (new)if replacement is specified in the service manualFind on Amazon → |
| 04 | Heat-resistant grease for glow plug threadsFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
11- diesel compression tester (gauge up to 4-5 MPa / 40-50 bar) with a check valve in the tip Amazon →
- adapter for the glow plug hole or an injector simulator (special tool with M10 x 1.25 thread for testing without removing the glow plugs) Amazon →
- sockets and extensions Amazon →
- ratchet Amazon →
- torque wrench Amazon →
- glow plug socket Amazon →
- compressed air Amazon →
- clean rags Amazon →
- multimeter Amazon →
- battery charger Amazon →
- flashlight Amazon →
Step by step
30 steps · 6 stagesStage 1 of 6 Preparation 5 steps
- Make sure the battery is fully charged and the starter turns the engine over confidently. Do the test on the vehicle's own battery, without a jump pack: cranking speed should be about 200-250 rpm, and with a weak battery the readings will be too low.
- Do the test on a cold or slightly warm engine: after long running, oil additionally seals the rings and inflates the readings. There is no need to warm the engine up on purpose.
- Check the air filter: a clogged filter lowers the readings. Replace it before the test if necessary.
- Shut the engine off and let it cool so you don't get burned on the manifolds and glow plugs. Disconnect the negative battery terminal while removing parts.
- Prepare a V8 cylinder numbering diagram and a table for recording the pressure of each cylinder (8 values).
Stage 2 of 6 Accessing the glow plugs 5 steps
- Remove the decorative plastic engine cover and the plastic protective panels over the manifolds that get in the way of access to the cylinder heads.
- Photograph the glow plug connectors and wiring mounts so you can reassemble everything in the same order.
- Disconnect the glow plug connectors or power bus bars on each cylinder head and move the wiring harnesses aside without damaging the retaining clips.
- Blow out the wells around the glow plugs and injectors with compressed air so debris does not fall into the cylinder when you unscrew them.
- Remove glow plugs (or install the injector simulator) one at a time: unscrew the glow plug only in the cylinder you are testing at that moment. If you remove all the plugs at once, the engine spins faster and the readings are inflated. For the test, use an adapter with an M10 x 1.25 thread for the glow plug hole; determine the exact geometry and the option of testing without removing the glow plug from the tool kit you have.
Stage 3 of 6 Disabling fuel delivery 3 steps
- Disable injection so that no fuel is delivered while cranking: using the fuse and relay diagram in the engine compartment, find the fuse or relay for the EDU (injector driver unit) circuit and remove it. Do not disconnect the high-pressure sensor connectors on the fuel rail.
- Connect the negative battery terminal. Warning lights may come on in the instrument cluster: this is normal, and they will need to be cleared with a diagnostic scan tool after the test.
- Connect a scan tool, or monitor engine speed with a test light or oscilloscope if possible, to make sure cranking speed is within 200-250 rpm.
Stage 4 of 6 Testing 7 steps
- Unscrew the glow plug of cylinder 1. Keep the wrench strictly in line with the plug axis so you don't break the thin plug. If the plug is seized and turns hard, soak the threads with penetrating oil and let it sit.
- Screw the compression tester adapter into the hole. Tighten only by hand with light force so you don't damage the threads in the head; the seal must be airtight.
- Press the accelerator pedal all the way down (so the electronics don't interfere), turn the key or press the Start button, and crank with the starter for 5-7 seconds (about 4-6 compression strokes) until the needle stops rising.
- Record the pressure, release the needle to zero with the valve, and unscrew the adapter.
- Reinstall the glow plug in cylinder 1 (tightening torque per the manufacturer's specification; as a guideline for glow plugs of this type, 8-15 N·m (6-11 lb-ft)) and move on to the next cylinder. Before installing, coat the threads with heat-resistant grease.
- Repeat the test one by one for all 8 cylinders, recording each result. For consistency, crank for the same number of revolutions on each cylinder.
- If one cylinder is clearly lower, repeat the test on it to confirm. For diagnosis, you can pour about 10-15 mL of clean engine oil into the cylinder and repeat the test: if the pressure rises noticeably, the cause is worn piston rings or cylinder; if it does not change, look for leaking valves or a head gasket leak.
Stage 5 of 6 Evaluating the results 4 steps
- Compare the values against each other. The main criterion: the pressure spread between cylinders should not be large (for diesels, a guideline is no more than about 0.3-0.5 MPa; the exact limit is in the Toyota service manual).
- For the absolute value: in modern Toyota diesels, end-of-compression pressure is usually on the order of 2.5-3.5 MPa (25-35 bar); the exact minimum spec for the 1VD-FTV is in the Toyota service manual. A value much lower than in the other cylinders points to worn rings, a burned piston, poorly seated valves, or a blown head gasket.
- If the pressure is low in all cylinders at once, check the battery charge and starter condition, then repeat the test: low cranking speed lowers the result.
- If two adjacent cylinders on the same head show low pressure, suspect the cylinder head gasket.
Stage 6 of 6 Reassembly and check 6 steps
- Make sure all glow plugs are installed with the correct tightening torque (per the manufacturer's specification) and the seals and washers are in place.
- Reconnect the glow plug connectors and bus bars and secure the harnesses in their factory clips.
- Put the EDU fuse or relay back, then install the plastic protective panels and the decorative engine cover.
- Connect the scan tool, read and clear the codes that appeared while fuel delivery was disabled (for the rail pressure sensors and injectors).
- Start the engine (it may take 2-3 attempts to fill the system), let it idle, and check for leaks and smoke at the glow plug mounting points.
- Take a test drive and check that there are no fault codes in the engine control unit.
Common mistakes and warnings
- The glow plugs and their holes sit deep in the V8 valley, and the threads may be seized: if stripped, the cylinder head will need repair
- Work carefully and without side load; if you lack experience, it is better to leave the test to a repair shop
- Do not allow debris to get into the cylinders
- Do not use values for gasoline engines or from generic tables as the standard: compare the result against the Toyota service manual and the spread between cylinders
- The tightening torques and pressure specs in the text are approximate; check the exact values against the manufacturer's service manual