https://autopapyrus.com/catalog/lexus/lx/guides/fuel-injector-replacement/
Lexus LX 450d 1VD-FTV 4.5 V8 Diesel (2017): Fuel Injector Replacement
The 1VD-FTV injectors on 2017 vehicles are piezoelectric (Euro 5) with injection pressure up to 200 MPa, so the job demands spotless cleanliness and careful work. Typical reasons for replacement: codes P0201-P0208 (piezo injector failure), loss of power, check engine light, smoke, and rough running. After installing the new injectors, you must register their codes (ID/QR) in the engine control unit. This guide covers replacing the full set; the procedure for a single injector is the same, but codes are registered only for the replaced ones.
Key figures
- Injection pressureup to 200 MPa. On Euro 5 engines the fuel in the lines is under enormous pressure, so do not open the lines on an engine that has just been shut off, and allow a waiting period (step 3)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: removed injector, its clamp and bolt
- 1Injector connector on top: disconnect it and photograph the layout.
- 2High-pressure line fitting: points upward from the cast part; undo the line with a split socket while a second wrench holds the fitting, then plug it at once.
- 3Clamp plate: curved plate with a tab; remember which cylinder it came from.
- 4Clamp bolt: stretch bolt, single use, fit a new one on assembly.
- 5Heat washer on the injector tip: pull the old one with a puller and fit a new one.
- 6Fitting dust seal: pry off with a thin screwdriver, fit a new one on assembly.
Parts
10| № | Part |
|---|---|
| 01 | Denso Common Rail piezo injectors for 1VD-FTV (Euro 5), complete8 pcs, current revision for the model yearFind on Amazon → |
| 02 | Injector heat-insulating seats (thermal washers), set8 pcsFind on Amazon → |
| 03 | Injector return line copper washersFind on Amazon → |
| 04 | Injector inlet fitting O-rings and dust sealsFind on Amazon → |
| 05 | Injector clamp bolts (stretch-type, single-use)newFind on Amazon → |
| 06 | Cylinder head cover gasketsif covers are removedFind on Amazon → |
| 07 | Intake pipe gaskets/sealsFind on Amazon → |
| 08 | Coolantas neededFind on Amazon → |
| 09 | Engine oilas neededFind on Amazon → |
| 10 | Diesel fuel for priming the systemFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
10- Socket set and ratchet Amazon →
- torque wrenches (a low-range one for the clamp bolts and a high-range one for the line nuts) Amazon →
- split-type (crowfoot/flare-nut) socket for high-pressure line nuts Amazon →
- injector puller (slide hammer) Amazon →
- injector seat/sleeve puller (copper seat remover) Amazon →
- brush and cleaner for injector bores Amazon →
- copper paste Amazon →
- caps for open fittings Amazon →
- clean compressed air Amazon →
- Toyota-compatible diagnostic scanner (Techstream or equivalent) for registering injector codes Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
35 steps · 7 stagesStage 1 of 7 Diagnosis and preparation 5 steps
- Connect the scanner and read the codes. Confirm which cylinder is faulty (P0201-P0208 correspond to cylinders 1-8). If needed, check the per-cylinder corrections and fuel delivery balance in data mode to make sure the problem is the injector and not the wiring or the fuel.
- Write down the codes of the old injectors and photograph the connectors. Check for current Toyota service bulletins on 1VD-FTV injectors: Toyota replaced some Euro 5 injectors with modified ones.
- Shut off the engine and let it cool to a safe temperature. Rail pressure must drop: wait at least 10-15 minutes after switching off the ignition, and do not open high-pressure lines on a hot engine or while under pressure.
- Put the vehicle on a lift or level ground and set the parking brake. Disconnect the negative battery terminal and wait 5-10 minutes.
- Thoroughly wash and blow off the top of the engine: dust and dirt in the injector bores and on the fittings are unacceptable.
Stage 2 of 7 Accessing the injectors 4 steps
- Remove the engine covers, air ducts and intake pipes that block access to the cylinder heads (air filter, intercooler pipes, etc., as needed). Cover all open intake openings with clean cloth or plugs.
- Disconnect the injector connectors and any harnesses in the way, and photograph the layout. Label the harnesses by cylinder.
- If necessary, remove the components that block access to the rails and head covers (crankcase ventilation hoses, wiring brackets, cooling system/EGR components, depending on the vehicle's configuration).
- Remove the cylinder head covers (left and right) if the injectors are located under them. Photograph any marks on the parts and reference points for their positions. Keep the cover fasteners in order.
Stage 3 of 7 Removing the injectors 7 steps
- Loosen and disconnect the high-pressure lines from the injectors and the rail (4 lines per bank, 8 in total). Do not bend or deform the lines: if deformed, they must be replaced. Use a split-type socket, with a second wrench holding the fitting. Immediately cap the rail and injector fittings with clean caps.
- Remove the return (fuel return) line: unscrew the banjo bolts/fittings, discard the copper washers, and install new ones during assembly.
- Carefully pry off and remove the dust seals/inlet seals of the injector fittings (using a thin flat screwdriver in the dedicated slot).
- Unscrew the injector clamp bolts. Remember which clamp belongs to which cylinder: on some cylinders the clamps differ. The bolts are single-use, so replace them with new ones.
- Remove the injectors. If they are stuck, use an injector puller or slide hammer, do not use jerking force, and do not pry on the connector housing. Do not rock the injectors sideways across their axis, to avoid damaging the bore.
- Immediately cover the open bores with a clean lint-free cloth or a plug so that no dirt gets into the cylinders.
- Remove the old heat-insulating seats and seals from the bores with a special puller. Clean the injector bores with a soft brush and a suitable cleaner, without scratching the seating surfaces. Blow out with compressed air (carefully, directed away from yourself).
Stage 4 of 7 Installing the new injectors 8 steps
- Inspect the bores: there should be no carbon buildup, scratches or signs of combustion gas leakage. If there are signs of gas leakage or damage to the seating surface, the cylinder head needs repair (for some defects Toyota recommends replacing the head).
- Install the new heat-insulating seats and seals in the bores. Use only parts that match your injector version.
- Lightly coat the body of the new injector with copper paste in the seating area (as required by the manufacturer's instructions), keeping it off the nozzle tip and contact surfaces.
- Insert the injector into the bore all the way in, straight, without tilting. Fit its own clamp in place (on the correct cylinder).
- Tighten the new clamp bolts evenly, in several passes. Use the torque and angle specified by the manufacturer for 1VD-FTV bolts (these are stretch bolts; do not take the torque and angle from other engines).
- Install the new dust seals/seals on the injector inlet fittings.
- Install the return line with new copper washers. Tighten the banjo bolts to the manufacturer's specification (usually low, in the range of 10-30 N·m (7-22 lb-ft), but check for your line).
- Install the high-pressure lines. First thread the nuts on by hand, then tighten them with a torque wrench and split-type socket to the manufacturer's specification for 1VD-FTV lines. If a line was previously removed and deformed, replace it.
Stage 5 of 7 Reassembly 4 steps
- Install the cylinder head covers with new gaskets. Tighten the fasteners in the proper sequence, using the manufacturer's torque specification for 1VD-FTV covers.
- Connect the injector connectors according to the cylinder labels. Make sure the harnesses do not touch sharp edges or hot parts.
- Install the removed intake pipes, air ducts, brackets and engine covers. Check that the clamps are secure, especially on the pipes after the turbocharger.
- Reconnect the negative battery terminal.
Stage 6 of 7 Registration and priming 4 steps
- Turn the ignition on (do not start the engine) and connect the scanner. Clear the codes and reset the adaptations, if the procedure calls for it.
- Register the codes (ID/QR) of the new injectors in the ECU through the scanner, cylinder by cylinder. Without registering the codes the engine will run unevenly, and errors and increased fuel consumption are possible.
- Prime the fuel system: if there is a manual priming pump on the filter, pump it until firm, then cycle the ignition on and off several times. Starting may take several attempts of 10-15 seconds each with pauses.
- Start the engine and let it idle. Inspect all high-pressure connections and the return line for leaks and air ingress. Fuel leaks are unacceptable.
Stage 7 of 7 Verification 3 steps
- Check data mode: per-cylinder corrections, rail pressure, and no codes. Perform the fuel delivery calibration/learning using the scanner procedure, if available.
- Warm the engine up to operating temperature and take a 10-15 km test drive under varying loads. Recheck for codes and fuel leaks.
- After 100-200 km, inspect the line and return connections for leaks. Replace the fuel filter if you suspect fuel contamination (the old injectors may have broken down and clogged the system with fine metal particles).
Common mistakes and warnings
- The high-pressure fuel system (up to 200 MPa) is dangerous: a jet of fuel can penetrate skin
- Do not loosen lines right after the engine stops, and certainly not while it is running
- The job requires cleanliness and special tools; if you have no experience with Common Rail, leave it to a specialist shop
- When a piezo injector fails, excess fuel can enter the cylinder and damage the piston, so do not put off replacement
- If the injectors failed because of metal debris (high-pressure pump disintegration), the rails, lines and pump must also be replaced, otherwise the new injectors will fail again
- The torque values in the text are approximate; verify exact values against the manufacturer's specifications