← Pajero Sport Mitsubishi Pajero Sport repair manuals →

Mitsubishi Pajero Sport (second generation, KH): Climate Control Panel Removal and Repair

The climate control panel on the Pajero Sport II usually fails for one of these reasons: the backlight or buttons stop working, a knob skips, solder joints on the board fail, or the unit no longer controls the blend/mode doors and the blower. The exact factory procedure for the KH was not found in public sources, so what follows is the general approach for vehicles in this class. Check the fasteners and clips on your version of the panel as you go.

DifficultyMedium Time1.5-3 hoursremoval, disassembly, soldering, installation Steps13

Parts

5
№PartGenuine part no.
01 Complete heater and A/C control unit (climate control panel)Find on Amazon → 7820A306
02 Climate panel backlight bulbs or LEDswhen repairing the panelFind on Amazon →
03 Climate panel buttons and knobsif wornFind on Amazon →
04 Electrolytic capacitorswhen repairing the boardFind on Amazon →
05 Solder with fluxFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

8
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

13 steps
  1. Park the vehicle on a level surface, turn off the engine and disconnect the negative battery terminal. Wait 5-10 minutes so the capacitors in the safety system modules can discharge. This keeps the airbags from deploying and prevents damage to electronic modules.
  2. Before disassembly, find the cause of the problem. Turn the ignition on and check whether the backlight comes on, whether all buttons and knobs work, whether the blower runs at every speed, and whether the air distribution modes and temperature change. This tells you what to repair: the panel board or the actuators (door servo motors).
  3. Check the heater and A/C fuses in the fuse boxes (cabin and under-hood). Ratings and locations are shown on the box cover. A blown fuse or a bad relay often looks like a failed panel.
  4. Remove the decorative trim bezel around the climate control panel. It is usually held by clips. Pry gently with a plastic trim tool, starting at a corner, and do not press hard on the plastic. If the bezel is connected to the center console or the head unit, remove those parts first.
  5. Remove the climate control panel mounting screws. They are usually on the front under the bezel or on the sides. Support the panel so it does not hang by the wiring harness.
  6. Carefully pull the unit toward you and disconnect the connectors. Remember or photograph the position of each connector. Press the locking tab rather than pulling on the wires. If there is a cable or linkage for a door actuator, disconnect it as well.
  7. Disassemble the unit on a workbench. Release the plastic clips on the housing, remove the knobs (they usually pull straight off the shaft) and take out the board. Photograph the position of the parts before disassembly.
  8. Inspect the board. Look for darkened or cracked solder joints, especially near connectors and high-power components, bulging or leaking capacitors, and signs of moisture and oxidation. Replace failed capacitors with new ones of the same capacitance and the same or higher voltage rating. Reflow any suspect solder joints with a 25-40 W soldering iron, taking care not to overheat the traces.
  9. If the backlight does not work, replace burned-out bulbs or LEDs with ones of the same size and power. Do not install brighter ones, or they will overheat the plastic.
  10. If the problem is with the buttons or knobs, clean the contacts with contact cleaner. Replace worn buttons or encoders (rotary position sensors in the knobs). If the board is badly damaged, it is simpler and more reliable to install a complete unit.
  11. Reassemble the unit in reverse order. Install the knobs and snap the housing shut. Before mounting the unit in place, connect the connectors, reconnect the battery, turn the ignition on and check all functions.
  12. Turn the ignition off, disconnect the battery, secure the unit with the screws and snap the bezel into place. Tighten the screws snug, without overtightening, so you do not strip the plastic mounts. There are no specified torque values for these screws.
  13. Reconnect the battery. If the unit uses door calibration, it runs automatically when the ignition is turned on. Check all modes and the temperature control for several minutes.

Common mistakes and warnings

  • Airbag wiring and other systems' wiring run near the panel
  • Work only with the battery disconnected and do not pull on the harnesses
  • Do not heat the board above 300-350 °C (572-662 °F) and do not keep the soldering iron on one spot for more than a few seconds
  • If the climate control still does not work after the repair, or the fault is in the actuators or the harness, a scan tool diagnosis is needed
  • If you have no soldering experience, it is better to take the unit to an electronics repair shop
Spotted a mistake? Tell us →

Test yourself