← Micra Nissan Micra repair manuals →

Nissan Micra (K13): Brake System Bleeding

Bleeding is needed after replacing the fluid, hoses, calipers or master cylinder, and also when the pedal feels "spongy." Fluid is pushed through each circuit until a clean stream without bubbles comes out of the bleeder screw. Wheel order: rear right, front left, rear left, front right. It is easier to work with a helper.

DifficultyMedium Time1-1.5 hours Steps13

Part

№Part
01 DOT 4 brake fluidabout 1 L (1.1 qt)Find on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 7 more. See manuals →

Step by step

13 steps
  1. Park the car on a level surface, apply the parking brake and turn off the engine. Lift the car and remove the wheel you are starting with, or reach the bleeder screw through the wheel arch. You can remove the other wheels one at a time.
  2. Before starting, disconnect the ABS unit connectors or remove the negative terminal from the battery. The ignition is off. This protects the hydraulic unit from air getting in and from the pump accidentally turning on.
  3. Open the hood and wipe the reservoir cap so dirt does not get into the system. Draw the old fluid out of the reservoir with a syringe and top up with fresh fluid to no lower than the halfway mark. During bleeding, watch the level and do not let it drop below MIN. If the reservoir runs empty, air will get into the system and you will have to start over.
  4. Clean the dirt off the bleeder screw on the rear right wheel. Fit the clear tubing onto it and put the other end into a container with a small amount of fresh fluid. This way air will not be drawn back in.
  5. Your helper presses the brake pedal firmly to the floor 4-5 times and keeps it pressed.
  6. While the pedal is held down, loosen the bleeder screw half a turn and let the air and fluid out. Tighten the screw right away, before the helper releases the pedal. Then the helper slowly releases the pedal.
  7. Repeat steps 5-6 until clean fluid without bubbles comes out of the tubing. Do not forget to top up the reservoir.
  8. Tighten the bleeder screw. The torque for a bleeder screw is usually low, approximately 7-9 N·m (5-7 lb-ft) (check the exact value in the manufacturer's service manual). Do not overtighten: the screw can be sheared off. Remove the tubing and put the cap on.
  9. Repeat steps 4-8 in this order: front left, rear left, front right.
  10. Reconnect the ABS connectors or the battery terminal. Bring the fluid level in the reservoir up to the MAX mark and close the cap.
  11. Press the pedal 10-15 times. It should feel firm, with a high and consistent travel, and should not sink when held down. If the pedal is soft, repeat the bleeding. If air remains, it may not be possible to purge it without diagnostic equipment for the ABS hydraulic unit.
  12. Install the wheels and tighten the lug nuts in a crisscross pattern. Take the lug nut torque from the manufacturer's service manual. Lower the car, then retighten the nuts to the final torque.
  13. Start the engine, check the pedal once more and make sure there are no leaks at the bleeder screws and connections. Take a test drive at low speed and check the brakes in a safe area.

Common mistakes and warnings

  • The brake system is critical to safety
  • If you have no experience, leave the job to a repair shop
  • Brake fluid damages paint, so wash off any splashes with water right away
  • Dispose of drained fluid properly and do not reuse it
  • Never drive if the pedal is soft or sinks to the floor
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →