https://autopapyrus.com/catalog/renault/duster/guides/camshaft-replacement/
Renault Duster 2.0 16V F4R (2017): Camshaft Replacement
The F4R camshafts sit in the cylinder head under the valve cover and are driven by the timing belt. The job requires fully disassembling the timing drive, so the belt, rollers and tensioner are replaced together with the camshafts. The keys to success are setting the timing exactly by the marks and locking tools, following the correct tightening sequence for the camshaft bearing caps, and keeping everything clean. Check the exact torque values for the bearing caps and valve cover against the manufacturer's service manual; the values below are approximate.
Diagram: where the camshaft pulleys, valve cover and right engine mount are
- 1Pulley with phaser on one of the camshafts: toothed rim for the timing belt, nut in the centre. Remove it while holding the shaft with a holder or a wrench on the flats, not a screwdriver.
- 2Pulley of the second camshaft with a bolt on the shaft end. Remember which pulley sits on which shaft and hold the shaft when removing it.
- 3Valve cover over both shafts, sealed with sealant. Loosen the bolts from the edges to the centre and separate the cover with a plastic scraper.
- 4Right engine mount below the pulleys: before removal support the engine with a jack through a wooden block under the oil pan.
- 5Mark on the pulley: before removing the belt the pulley marks and the locking tools must align, otherwise do not continue.
Parts
9| № | Part | Genuine part no. |
|---|---|---|
| 01 | F4R camshafts (intake and exhaust)as a set if both are wornFind on Amazon → | |
| 02 | Camshaft sealsFind on Amazon → | 7701478550 |
| 03 | Valve cover gasket with spark plug well sealsFind on Amazon → | |
| 04 | Timing belt kit (belt, rollers, tensioner)must be replaced during this jobFind on Amazon → | 130C17529R |
| 8671019548 | ||
| 05 | Valve cover sealantFind on Amazon → | |
| 06 | Engine oil for assemblyFind on Amazon → | |
| 07 | Coolantfor topping offFind on Amazon → | |
| 08 | Engine oilfor topping offFind on Amazon → | |
| 09 | Lifters or hydraulic lash adjustersif worn; replace as a set if the camshaft comes out together with themFind on Amazon → |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
12- torque wrench (5-120 N·m (4-89 lb-ft)) Amazon →
- socket set with ratchets Amazon →
- Torx and hex bit set Amazon →
- crankshaft and camshaft locking tools (TDC pin and camshaft locking tools for the F4R) Amazon →
- camshaft pulley holding tool Amazon →
- seal installer Amazon →
- seal puller Amazon →
- oil syringe Amazon →
- plastic scraper for old sealant Amazon →
- Plastigauge or calibrated wire feeler for checking clearances Amazon →
- marker Amazon →
- clean rags Amazon →
Step by step
20 steps- Let the engine cool down and disconnect the negative battery terminal. Remove the engine undershield. Drain the coolant only if the hoses are in the way. Remove the air duct, the air filter with its hoses, and the decorative engine cover.
- To reach the timing belt, remove: the right engine mount (first support the engine from below with a jack, using a wooden block under the oil pan), the accessory drive belt, the crankshaft pulley, and the timing belt covers. Before removing the pulley, take a photo of the accessory drive belt routing.
- Disconnect the ignition coils, the sensor connectors on the valve cover, the crankcase ventilation hose, and any fuel or vacuum lines that block removal of the cover. Label everything you disconnect. Remove the coils and spark plugs so the crankshaft can be turned by hand.
- Turn the crankshaft in its normal direction of rotation by the pulley bolt to TDC of cylinder 1. Insert the locking pin into the flywheel or block hole (TDC pin) and install the camshaft locking tools. The marks on the pulleys and the factory locking tools must line up. If the marks do not line up, do not continue; find the cause first.
- Use a marker to mark the direction of rotation on the timing belt. Release the tensioner and take the belt off the camshaft pulleys. Do not turn the crankshaft after this: the pistons and valves may collide.
- Remove the camshaft pulleys or the phaser. Hold the camshaft against turning with the special tool or with an open-end wrench on the flats of the camshaft; do not lock the pulley with a screwdriver. Remember which pulley sits on which camshaft. Check the tightening torques for the pulley and phaser bolts against the service manual: for the bolts that secure the camshaft pulleys the values are usually high (tens of N·m, and the phaser may be around 100 N·m (74 lb-ft)), so use an accurate torque wrench.
- Remove the valve cover: loosen all bolts from the edges toward the center, evenly, in several passes. The cover is seated on sealant; carefully separate it with a plastic scraper and do not damage the sealing surface.
- Mark or photograph the position of the camshaft bearing caps. The caps are marked with numbers and arrows, and each can only be installed in its own location and orientation.
- Loosen the bearing cap bolts evenly, in several passes, from the edges toward the center, so the camshaft does not bend. Remove the caps and lift out the camshafts together with the seals, laying them out in order.
- Inspect the camshaft journals and the bearing seats in the cylinder head for scoring, stepped wear, heat discoloration and deep scratches. Measure the cam lobe height and the clearances using Plastigauge or a wire feeler. Allowable clearances and wear limits are per the manufacturer's specifications. If the bearing seats in the head are scored, replacing the camshaft alone will not be enough; the head will need to be repaired or replaced.
- Thoroughly clean the valve cover and cylinder head sealing surfaces of old sealant and degrease them. Make sure debris and sealant do not get into the oil passages or onto the belt.
- Lubricate the journals and lobes of the new camshaft with engine oil or special assembly lube. Lay the camshafts in the bearing seats in the position that corresponds to the timing marks (the cylinder 1 lobes pointing as shown in the factory diagram, and the locking tools must slide into the slots in the camshafts).
- Apply a thin layer of sealant to the mating surfaces of the caps where required (usually the end cap) and install the caps in their own positions according to the marks. Tighten the bearing cap bolts evenly, in several passes, from the center toward the edges, to the specified torque (for caps like these it is usually a low torque, roughly 8-15 N·m (6-11 lb-ft)). Do not tighten by feel: overtightening distorts the camshaft and the bearing seats.
- Press in the new camshaft seals evenly with the installer, without tilting, with a light film of oil on the seal lip. Do not reuse old seals.
- Install the pulleys and phaser on their own camshafts. Tighten the bolts while holding the camshaft against turning, to the specified torque. For the phaser bolt on this engine family the approximate value is on the order of 100 N·m (74 lb-ft), but check the exact figure for your engine version.
- Install the new valve cover or gasket on clean surfaces. Tighten the bolts in several passes from the center toward the edges, with a low torque (usually about 8-12 N·m (6-9 lb-ft)); check the exact value and sequence in the service manual. Install the coils, spark plugs, connectors and hoses.
- Install the new rollers and tensioner, then the timing belt: first onto the crankshaft pulley, then in the direction of travel through the camshaft pulleys and the water pump, and onto the tensioner last. The locking tools and marks stay in place during this. Tension the belt following the manufacturer's procedure (the tensioner marks are aligned to the specified position). Tighten the tensioner roller to the specified torque.
- Remove all locking tools and turn the crankshaft two full turns by hand in its normal direction of rotation. Install the locking tools again: they must go in freely. If they do not go in or the marks do not line up, remove the belt and repeat the installation.
- Install the crankshaft pulley with a new bolt (if the service manual requires replacement) and tighten it to specification. Install the right engine mount, the accessory drive belt, the air filter, and the undershield, and reconnect the battery. Top off the oil and coolant as needed.
- Start-up and check: crank the engine with the starter for a few seconds without starting it to build up oil pressure, then start the engine. Brief hydraulic lash adjuster noise and ticking on a cold start are acceptable and should go away as the engine warms up. Check for leaks at the valve cover and the seals, and make sure there are no Check Engine codes. After the first 500-1000 km, check the oil level and look for leaks.
Common mistakes and warnings
- The F4R is an interference engine: if the timing is set incorrectly, the pistons can hit the valves, so do not turn the crankshaft with the timing belt removed and check the marks twice
- If you have no experience with timing drives and torque wrenches, it is better to leave the job to a repair shop
- The torque values in this guide are approximate; check the exact values for the bearing caps, valve cover, pulleys and tensioner against the manufacturer's service manual
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Renault
Louis Renault (1877–1944) was interested in electricity and mechanics from an early age, and he was destined to become…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →