Autopapyrus · Renault Duster 1.5 dCi K9K 109 hp (2015)
https://autopapyrus.com/catalog/renault/duster/guides/glow-plug-replacement/
https://autopapyrus.com/catalog/renault/duster/guides/glow-plug-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Renault Duster 1.5 dCi K9K 109 hp (2015): Glow Plug Replacement
Glow plugs on the K9K make cold starts easier. Signs of wear: long cranking in cold weather, white smoke at startup, a glow plug warning light, or a preheat system fault code. Replace all 4 plugs as a set. The main risk is snapping an old plug off in the cylinder head, so work on an engine that is warm but not hot, and never apply sudden force.
Diagram: where the K9K glow plugs are and how to unscrew them
Tap to enlarge
- 1Glow plug: sticks out of the head under the connector, four in total, replace all as a set. Unscrew smoothly without jerking.
- 2Electrical connector on the plug: remove it before unscrewing; if the terminal has a nut, undo it and remember the order of parts.
- 3Aluminium cylinder head: its thread is soft, so start the new plug by hand without cross-threading.
- 4Long thin-wall 10 mm socket with extension and ratchet: fit it exactly in line with the plug and turn without force.
- 5New plug: M10x1 thread, 10 mm hex. Length and pin shape must match the old one; lightly grease the thread, not the pin.
- 6Oil filler cap: a landmark on the engine next to the plugs.
- 7Injector lines: a landmark, do not touch them, only blow dirt away around the plugs.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | Glow plugs for 1.5 dCi K9K, pencil-type, low-voltage, M10x1, 10 mm hex4 pcs (one per cylinder)Find on Amazon → | AlternativesNGKBoschBeru |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- Long 10 mm socket (deep, thin-wall) Amazon →
- extension Amazon →
- ratchet Amazon →
- low-range torque wrench Amazon →
- multimeter Amazon →
- magnetic pickup tool Amazon →
- compressed air or a brush and vacuum Amazon →
- high-temperature anti-seize for glow plug threads Amazon →
- wrench or socket for the terminal nut (size depends on the connector, usually small, 7-8 mm) Amazon →
Step by step
22 steps · 4 stagesStage 1 of 4 Diagnosis and preparation 6 steps
- Make sure the glow plugs are the cause. Disconnect the connectors from the glow plugs and use a multimeter to measure resistance between each plug terminal and ground. A good plug reads a fraction of an ohm (about 0.4-1 ohm); an open circuit reads infinite. If in doubt, replace all four.
- Let the engine cool to a warm state. A cold head is generally safer, but a fully cooled aluminum head with carbon-fouled threads can grip the plug harder. Ideally the engine should be slightly warm, not hot.
- Park the car on level ground, shut off the engine and remove the key.
- Open the hood. Disconnect the negative battery terminal.
- Remove the decorative plastic engine cover and, if needed, any air ducts and hoses in the way, to get access to the cylinder head and the glow plugs.
- Blow out the area around each glow plug with compressed air (or wipe it with a brush and vacuum it) so dirt does not fall into the cylinder when the plugs are removed.
Stage 2 of 4 Removing the old glow plugs 6 steps
- Disconnect the electrical connector or power bus bar from each glow plug. If the terminal has a nut, unscrew it and remove the washer, noting the order of the parts.
- Before unscrewing, apply a small amount of penetrating oil to the glow plug threads and wait a few minutes.
- Fit the long 10 mm socket onto the glow plug exactly in line with it, so you do not put it at an angle.
- Unscrew the glow plug smoothly, without jerking. If it is tight, turn it back in 1/8 turn and then unscrew it again, repeating several times. Do not use force: glow plugs are brittle and break.
- Lift the plug out of its bore with a magnet or tweezers. Check that it is intact: a whole plug has its tip with no part broken off.
- If a plug breaks off, do not continue on your own: an extractor or partial removal of the cylinder head is needed, so it is best to take the car to a repair shop.
Stage 3 of 4 Installing the new glow plugs 5 steps
- Compare the new and old plugs for length, M10x1 thread and tip shape.
- Lightly coat the threads of the new plugs with high-temperature anti-seize, keeping it off the tip.
- Thread each plug in by hand until it seats, without cross-threading, so you do not strip the threads in the aluminum head.
- Tighten with a torque wrench. The torque for glow plugs of this type is usually 10-15 N·m (7-11 lb-ft); check the exact value against the manufacturer's specification. Do not overtighten.
- Reinstall the connectors or power bus bar and tighten the terminal nuts lightly (about 1-2 N·m (9-18 lb-in), per the specification), taking care not to bend the terminals.
Stage 4 of 4 Reassembly and check 5 steps
- Reinstall the air ducts, hoses and the decorative cover.
- Reconnect the negative battery terminal.
- Turn the ignition on without starting the engine and wait for the glow plug light to go out. Then start the engine and check that it starts confidently.
- Check for fault codes in the preheat circuit. If the warning light is on, read the codes with a diagnostic scanner and clear them.
- If the light or the fault code remains after replacement, check the relay and the preheat control unit.
Common mistakes and warnings
- Old glow plugs break easily in the cylinder head, especially after many years of service
- Do not use force and do not use a cheater bar on the extension
- If a plug breaks off, do not try to knock it out: take the car to a repair shop
- Torque values are approximate, so check the exact values against the manufacturer's specification
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Renault
Louis Renault (1877–1944) was interested in electricity and mechanics from an early age, and he was destined to become…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →