Autopapyrus · Skoda Fabia (6Y) 2007
https://autopapyrus.com/catalog/skoda/fabia/guides/front-wheel-bearing-replacement/
https://autopapyrus.com/catalog/skoda/fabia/guides/front-wheel-bearing-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Skoda Fabia (6Y) 2007: Front Wheel Bearing Replacement
The Fabia 6Y bearing is pressed into the steering knuckle, and the hub is pressed out of it. Pressing it out destroys the bearing, so once removed it can only be replaced. It is best to replace bearings in pairs on the same axle. Replace the axle nut, along with the self-locking knuckle nuts and bolts, with new ones every time you take the assembly apart.
Key figures
- Axle nut tightening torque50 N·m (37 lb-ft), then an additional 45° turn, step 26; tighten with the wheels off the ground, otherwise the bearing will be damaged
- Lug bolts120 N·m (89 lb-ft), steps 27 and 30; tighten in a crisscross pattern
- Caliper guide bolts28 N·m (21 lb-ft), step 23
- Stabilizer bar link nut40 N·m (30 lb-ft), step 21
- ABS sensor screw (hex)8 N·m (6 lb-ft), step 22; do not leave it any looser, or the sensor will rattle
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the wheel bearing is and what to remove to reach it
Tap to enlarge
- 1Driveshaft nut in the centre of the hub: loosen it with the wheels on the ground, remove it fully after the wheel is off, fit only a new one.
- 2Hub with bearing: the hub is pressed out of the bearing in the knuckle; the old bearing is replaced.
- 3Steering knuckle: remove the knuckle with the bearing from the strut by undoing the nut and bolt.
- 4Caliper on two guide bolts: remove the bolts, take the caliper off and hang it on wire.
- 5Brake hose: do not unscrew or stretch it; the caliper must not hang on it.
- 6ABS sensor: remove the screw and pull the sensor out of the knuckle; refit the screw to 8 Nm.
- 7Brake disc: comes off after the pads; the dust shield behind it is removed too.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Front wheel bearing, Fabia 6Y (complete assemblyor bearing only with retaining ring)Find on Amazon → | AlternativesSKFFAGSNRFebi |
| 02 | Self-locking axle (CV shaft) nutnewFind on Amazon → | |
| 03 | Self-locking steering knuckle nuts and boltsnewFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
10- jack and jack stands Amazon →
- lug wrench Amazon →
- torque wrench Amazon →
- 12-point socket for the axle nut Amazon →
- socket and open-end wrench set Amazon →
- ball joint and tie rod end puller Amazon →
- wire for hanging the caliper Amazon →
- press with drivers (or a bearing removal kit for on-vehicle pressing) Amazon →
- snap ring puller Amazon →
- copper grease for the mating surfaces Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 9 more.
See manuals →
Step by step
30 steps · 5 stagesStage 1 of 5 Preparation 5 steps
- Check whether the wheels have locking (anti-theft) lug bolts. If they do, find the key.
- Park the car on a level surface, put it in gear, and chock the rear wheels. Remove the hub cap from the center of the wheel.
- While the car is still on its wheels, loosen the axle nut by no more than 90°. Loosen the lug bolts. Have a helper press the brake pedal.
- Raise the front of the car, set it on jack stands, and remove the wheel.
- Prepare the new axle nut and the new knuckle nuts and bolts. Do not lubricate the threads of the outer CV joint on the axle shaft.
Stage 2 of 5 Removal 7 steps
- Remove the axle nut completely (the helper presses the brake pedal again), then release the pedal.
- Remove the two caliper guide bolts. Take off the caliper and hang it on a wire. Do not disconnect or stretch the brake hose.
- Remove the brake pads and the brake rotor. Remove the rotor dust shield.
- Remove the ABS sensor screw (hex) and pull the sensor out of the knuckle.
- Remove the stabilizer bar link nut (if it blocks access). Disconnect the tie rod end with a puller.
- Remove the ball joint bolt and lower the control arm. Knock or press the axle shaft out of the hub. Tie up the shaft so it does not hang from the joint.
- Remove the nut and bolt that secure the knuckle to the strut (the bolt is inserted with its tip pointing in the direction of travel). Slide the knuckle off the strut legs and take it to the workbench. Do not put any load on the axle shaft.
Stage 3 of 5 Bearing replacement 6 steps
- Secure the knuckle in a vise or on the press. Press the hub out of the bearing. The bearing is destroyed in the process.
- Remove the bearing retaining ring. Use a puller to remove the remains of the bearing's inner race from the hub.
- Press the bearing's outer race out of the knuckle, pushing on it with a driver equal in diameter to the race.
- Clean the knuckle bore of dirt and corrosion. Check that it is round and free of scoring. Remove any remains of the old retaining ring.
- Press in the new bearing, pushing only on the outer race, not the inner one. Install the new retaining ring in the groove. A click and an even seat in the groove mean the ring is installed correctly.
- Press the hub into the bearing, pushing on the inner race. Check that the hub turns freely, without binding or noise.
Stage 4 of 5 Installation 7 steps
- Install the knuckle on the strut. Tighten the new knuckle-to-strut nut and bolt. Torque: knuckle nut 60 N·m (44 lb-ft) + 90° (per spec for this nut, torque applied to the bearing housing).
- Insert the axle shaft into the hub. Install the control arm on the ball joint and tighten the ball joint bolt to the manufacturer's specification.
- Connect the tie rod end and the stabilizer bar link. Stabilizer link nut: 40 N·m (30 lb-ft). Tie rod end: to specification.
- Install the ABS sensor, screw: 8 N·m (6 lb-ft).
- Install the dust shield, brake rotor, pads, and caliper. Caliper guide bolts: 28 N·m (21 lb-ft).
- Thread on the new axle nut. It may only be tightened while the wheels are off the ground, otherwise the bearing will be damaged.
- Install the wheel and tighten the bolts by hand. Lower the car onto its wheels.
Stage 5 of 5 Tightening and check 5 steps
- Have a helper press the brake pedal. Tighten the axle nut to 50 N·m (37 lb-ft). For cars with power steering, turn it an additional 45°.
- Tighten the lug bolts to 120 N·m (89 lb-ft) in a crisscross pattern.
- Press the brake pedal fully several times to seat the pads against the rotor. Check the brake fluid level.
- Take a test drive. Listen for humming or knocking in turns. Check that the steering wheel does not pull to one side.
- After 50-100 km, recheck the lug bolt torque (120 N·m (89 lb-ft)).
Common mistakes and warnings
- This job involves the brakes and suspension, which are safety-critical
- If you lack experience and the right equipment (press, torque wrench), have a shop do the work
- Do not load the bearing while the axle nut is loose, and do not move the car without the axle shaft installed
- Use only new self-locking nuts and bolts, a new axle nut, and a new bearing retaining ring
- Check the manufacturer's specifications for the torque values that are not given here (ball joint bolt, tie rod end, caliper bracket hardware)
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Skoda
A detailed look at how the Škoda automotive brand came to be.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →