Autopapyrus · Toyota Alphard 3.5 V6 2GR-FE (2013)
https://autopapyrus.com/catalog/toyota/alphard/guides/spark-plug-replacement/
https://autopapyrus.com/catalog/toyota/alphard/guides/spark-plug-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Toyota Alphard 3.5 V6 2GR-FE (2013): Spark Plug Replacement
On the 2GR-FE V6, the front bank of spark plugs is accessible right away, while the rear bank (next to the firewall) is covered by the upper intake manifold. To replace all six plugs, you need to remove the wiper arms, the cowl panel (the grille below the windshield) and the plenum. The torque values below for the plenum and coil fasteners are approximate. Check the exact values against the manufacturer's service manual.
Key figures
- Spark plug tightening torqueset this on the torque wrench (step 16); overtightening can strip the thread in the engine25 N·m (18 lb-ft)
- New spark plug gapthe distance between the electrodes at the plug tip, check with a feeler gauge before installing (step 3)1.0-1.1 mm
- Old spark plug gap at which it is time to replace itthe electrodes are worn and the engine starts to start harderover 1.3 mm
- Which plugs to installiridium, replace all six at onceDenso SK20R11, 6 pcs
- Spark plug socketwith a rubber insert inside so the plug doesn't fall into the deep well (step 14)16 mm
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the spark plugs are and how to reach them
Tap to enlarge
- 1front plugs, 3 pcs, radiator side: in plain view. Unplug the connector, undo one bolt, pull out the coil, the plug is underneath
- 2rear plugs, 3 pcs, cabin side: hidden under the plenum. Remove the plenum first, then the same: coil, plug underneath
- 3plenum: the big ribbed part on top of the engine that carries the air. It is see-through on the diagram so the rear plugs show
- 4air filter: its housing and duct come off first, otherwise the plenum won't come out
- 5cowl panel: the plastic grille under the windscreen. It comes off together with the wipers to make room for the plenum
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Denso SK20R11 iridium spark plugs6 pcsFind on Amazon → | AlternativesNGK |
| 02 | Intake manifold (plenum) gaskets, set of 3Find on Amazon → | |
| 03 | Ignition coilsover 150,000 km (93,000 mi) and questionable condition; rear bank first (cylinders 1, 3, 5)Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- 10 Amazon →
- 12 and 14 mm sockets and wrenches Amazon →
- 16 mm spark plug socket with a rubber or magnetic insert Amazon →
- extensions with a universal joint Amazon →
- torque wrench (range up to 30 N·m) Amazon →
- feeler gauge Amazon →
- vacuum cleaner or compressed air Amazon →
- plastic-safe silicone grease Amazon →
- container for bolts Amazon →
Step by step
27 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Wait until the engine has cooled down completely: the plugs thread into an aluminum cylinder head, and a hot thread is easy to strip.
- Park the car on a level surface and disconnect the negative battery terminal.
- Prepare the new plugs and check the gap with a feeler gauge: for a new plug it should be 1.0-1.1 mm. Do not press on or bend the iridium electrode with the gauge or your fingers. If needed, adjust only the ground (side) electrode.
- Remove the decorative plastic engine covers, if installed.
Stage 2 of 5 Accessing the rear bank 6 steps
- Remove the wiper arms and the plastic caps at their base, then remove the arm mounting nuts.
- Remove the hood seal at the cowl panel, remove the bolts and clips, and take off the cowl panel (the grille below the windshield). If the wiper motor is in the way, disconnect its wiring connector and unbolt it with a 10 mm wrench.
- Remove the air intake housing with the duct and the mass airflow sensor, and disconnect the ventilation and fuel vapor hoses on the plenum. Label the connectors and hoses.
- Disconnect the sensor connectors, vacuum hoses, and the throttle cable or throttle body connector from the plenum.
- Remove the plenum mounting bolts and nuts. Don't forget the two hidden rear support bolts, which are removed with a 12 or 14 mm wrench. Lift off the plenum and remove the old gaskets.
- Plug the intake ports with a clean lint-free cloth so nothing falls into the cylinders.
Stage 3 of 5 Replacing the spark plugs 8 steps
- Disconnect the ignition coil connectors.
- Remove the coil bolts (10 mm wrench) and carefully pull out the coils. Label the coils by cylinder.
- Blow out or vacuum the spark plug wells so that dirt doesn't get into the cylinder.
- Remove the old plugs with the 16 mm socket and an extension. Inspect them: the color of the deposits and the condition of the electrodes will show the condition of the cylinders.
- Start threading each new plug by hand only, using the extension without a wrench, so you don't strip the thread. Don't push sideways on the extension, or you could crack the ceramic.
- Tighten each plug with a torque wrench to 25 N·m (about 18 lb-ft). Do not overtighten: the thread is in an aluminum head.
- Apply a thin layer of silicone grease to the rubber boot of the coil, press the coils on until they click into place, and tighten their bolts to a moderate torque (approximately 7-10 N·m (5-7 lb-ft), check the exact value in the service manual).
- Connect the coil connectors and make sure the wires are not pinched.
Stage 4 of 5 Reassembly 5 steps
- Remove the plugs from the intake ports and install new plenum gaskets. Do not reuse the old gaskets: an air leak will cause lean mixture codes (P0171, P0174).
- Install the plenum, not forgetting the two rear support bolts, and tighten the fasteners evenly, in the range of 15-25 N·m (11-18 lb-ft) for M8 bolts (check exact values in the service manual).
- Reconnect the vacuum hoses, ventilation hoses, sensor connectors, and the throttle body. Install the air filter housing with the duct and the mass airflow sensor.
- Install the wiper motor (if you removed it), the cowl panel, the seal, and the wiper arms. Set the arms in their original position.
- Reconnect the battery.
Stage 5 of 5 Checking 4 steps
- Start the engine and let it idle. Listen for air leaks and misfires.
- Check the instrument cluster: the check engine light should not be on. If necessary, clear the codes with a scan tool.
- Check the operation of the wipers and washer, and the hood gap at the cowl panel.
- After 100-200 km, check whether any air leaks or knocking have appeared.
Common mistakes and warnings
- Do all work on fuel hoses with the engine cold and away from open flame
- Do not tighten the spark plugs beyond the specified torque: the thread in an aluminum head strips easily
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →