← Crown

Toyota Crown (S180): Removing and Installing the Pillar Trim and Headliner

The headliner and pillar trim on the Crown S180 are held by plastic clips and a few screws. Behind the trim on the front, center and rear pillars, and along the roof, run the curtain airbags and their wiring. The order of work therefore matters: first disconnect power, then remove the small parts, then the pillars, and only after that lower the headliner.

DifficultyHard Time3-5 hours Steps16

Key figures

  • Wait after disconnecting the battery
    at least 90 seconds. Wait before any work near the curtain airbags (step 1)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

3
№PartGenuine part no.
01 Pillar and headliner trim clips and push pins set (, Toyota Crown S180)kitFind on Amazon →
02 Headliner assemblywhen replacing the trim itselfFind on Amazon → 63311-30570-A0
63311-30570-B0
63311-30570-B1
03 Decorative pillar coversif only these need replacingFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

6

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

16 steps
  1. Park the vehicle on a level surface, turn the ignition off and disconnect the negative battery terminal. Wait at least 90 seconds so the SRS system capacitors can discharge. For this model, check the exact wait time in the manufacturer's service manual. Do not touch the yellow airbag connectors.
  2. Flip down the sun visors. Remove the mounting covers, unscrew the screws and take out the visors with their holders. Disconnect the connector if the visor has a vanity mirror light.
  3. Remove the overhead grab handles above the doors. Pry off the screw covers, remove the screws and take off the handles. If the handles are on a spring-loaded pivot, don't lose the spring.
  4. Remove the dome light and the console with the map lights. Carefully pry off the lens with a plastic trim tool and disconnect the connectors. If the roof has a sunroof, remove its trim and sunshade according to the design of your trim level.
  5. Remove the interior rearview mirror together with the trim cover at its mount if it is in the way. Disconnect the sensor connector if equipped.
  6. Remove the door opening weatherstrips. Simply pull the rubber off the flange around the perimeter of the front and rear doors to free the lower edges of the pillar trim.
  7. Remove the front pillar (A) trim. Pull the edge toward the cabin; the clips release with a distinct click. Work from top to bottom. Don't yank it, so you don't break the clip legs or damage the curtain airbag that sits right behind the trim.
  8. Remove the center pillar (B) trim panels: first the upper part, then the lower. Before that, remove the seat belts, or unbolt only the upper belt anchor point if it is covered by the trim. For the belt anchor installation torque, follow the manufacturer's specification. This is a safety item, so tighten it strictly with a torque wrench.
  9. Remove the rear pillar (C) trim and the rear window trim panels. First remove the rear parcel shelf and the upper trim panels of the rear seatbacks if they cover the lower clips.
  10. Check that no screws or clips holding the headliner around its perimeter remain and that all lighting connectors are disconnected.
  11. Release the headliner clips around the edges, starting at the front edge by the windshield. Lower the headliner together with a helper, supporting the rear part. Don't bend the panel: a crease stays forever.
  12. Remove the headliner through the opening of one of the rear doors, or through the trunk with the seatbacks folded. Go by your version: with a sunroof the panel is larger and harder to remove. Lay the headliner on a flat surface or hang it so it doesn't get creased.
  13. Installation is done in reverse order. First bring the headliner into the cabin, connect the lighting connectors, press in the front clips, then the side and rear ones. Replace any broken clips with new ones.
  14. Install the pillar trim: insert the lower part into the slot, then press the clips along the length. Press it flat with your palm so there are no gaps. Put the door opening weatherstrips back on.
  15. Reinstall the handles, visors, mirror and dome light. For the exact torque of the small screws, follow the manufacturer's specification. They are tightened without much force so the plastic doesn't crumble.
  16. Reconnect the battery. Turn the ignition on and check: the SRS indicator should not stay lit, and the dome light, visor lights and sunroof should work. If the SRS light is on, don't drive; take the car to a repair shop to read the fault codes.

Common mistakes and warnings

  • Curtain airbags are located in the pillar trim and under the headliner. Do not break, pinch or drill near the wiring and airbag housings, and after the work the SRS indicator must go out. If you have no experience with passive safety systems, it is better to leave the job to a repair shop. The headliner design and removal order depend on the trim level, especially with a sunroof, so check the exact fasteners and torque specifications (including seat belt anchor bolts) against the manufacturer's service manual. 2005 model year vehicles are the S180, and the engine does not affect this procedure.
Spotted a mistake? Tell us →

Our articles

More articles →