Autopapyrus · Toyota Lite Ace (R40)
https://autopapyrus.com/catalog/toyota/lite-ace/guides/front-lower-ball-joint-replacement/
https://autopapyrus.com/catalog/toyota/lite-ace/guides/front-lower-ball-joint-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Toyota Lite Ace (R40): Front Lower Ball Joint Replacement
The Lite Ace R40 has a control arm front suspension. The ball joint sits in the lower arm and connects it to the steering knuckle. The exact design depends on the trim and version: the joint may be bolted to the arm or pressed into it. Check this once the arm is removed, or look it up in the catalog for your version. It is best to replace ball joints in pairs. A wheel alignment is required after the job.
Parts
4| № | Part | Alternatives |
|---|---|---|
| 01 | Front lower control arm ball joint1 per sideFind on Amazon → | AlternativesCTR555Lemförder |
| 02 | Cotter pinsnewFind on Amazon → | |
| 03 | Ball joint dust bootsif not included in the kitFind on Amazon → | |
| 04 | Retaining ringsif not included in the kitFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
11- Jack and jack stands Amazon →
- wheel chocks Amazon →
- lug wrench Amazon →
- socket and wrench set Amazon →
- ball joint separator (or pickle fork) Amazon →
- hammer Amazon →
- pry bar Amazon →
- torque wrench Amazon →
- a press or puller-type removal tool if the joint is press-fit Amazon →
- grease Amazon →
- new cotter pin Amazon →
Step by step
14 steps- Park the vehicle on level ground, set the parking brake, and chock the rear wheels. Loosen the front lug nuts a half turn.
- Raise the front end with a jack and support the vehicle on jack stands placed under the body. Remove the wheel.
- Check for play: use a pry bar to lift the lower arm near the knuckle. Noticeable play, a torn dust boot, or grease pushed out of the joint means the joint needs to be replaced.
- Remove the brake pads and caliper without disconnecting the brake hose. Hang the caliper from a piece of wire so the hose isn't stretched. If the brake rotor is in the way, remove it as well.
- Pull out the cotter pin and unscrew the castle nut of the ball joint at the knuckle. If the stud turns, hold it with a hex key or a screwdriver in the slot.
- Separate the stud from the knuckle with a ball joint separator or a pickle fork. Strike the knuckle eye, not the threads of the stud. If you hit the threads without a nut on them, they will be damaged.
- The lower arm is under torsion bar load. If the joint is bolted to the arm, remove its fasteners and take the joint off. If the joint is press-fit, before removing the arm, lock in the torsion bar adjustment position: make marks and write down the protrusion of the adjusting bolt. Only then remove the arm, and press the joint out with a press or a puller.
- Clean the seat of dirt and rust. The new joint must seat without tilting.
- Install the new joint (bolt it on or press it in until it stops). Tighten the fasteners with a torque wrench. The torque values for your version are approximate, so check the exact figures in the manufacturer's service manual. For bolted joints like this, Toyota typically specifies several tens of N·m, and about 100 N·m (74 lb-ft) for the stud nut at the knuckle.
- Insert the stud into the knuckle and tighten the castle nut to the specified torque. Then tighten it further to the nearest alignment of the slot with the hole, but do not back it off. Install a new cotter pin and bend its ends apart.
- If you removed the arm, reinstall it. The arm pivot fasteners must be final-tightened with the vehicle standing on its wheels, otherwise the bushings will tear quickly. Install the brake rotor, caliper, and pads. Tighten the caliper fasteners to spec.
- If the joint has a grease fitting, pump in grease until the boot swells slightly. If the joint is maintenance-free, skip this step.
- Install the wheel, lower the vehicle to the ground, and tighten the lug nuts in a crisscross pattern to spec (for this model, about 100-110 N·m (74-81 lb-ft); confirm the exact value in the service manual). Pump the brake pedal several times so the pads seat against the rotor.
- Drive the vehicle 5-10 km (3-6 miles), then recheck the lug nut torque and check for play again. Be sure to have a wheel alignment done.
Common mistakes and warnings
- Suspension and brakes are safety-critical systems
- A loose or incorrectly installed ball joint can lead to loss of control, so if you lack experience, it is better to leave this job to a repair shop
- Do not disassemble the torsion bar or release its adjustment without marking its position: the arm and torsion bar are under load
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →