https://autopapyrus.com/catalog/toyota/mark-x/guides/connecting-srs-airbag-connectors/
Toyota Mark X (X130): Connecting SRS Airbag Connectors
The SRS on the X130 includes driver and passenger front airbags, side airbags, curtain airbags and seatbelt pretensioners. All of them connect through yellow connectors with double locking. Connect them with the battery disconnected, follow the correct inspection order, and always read the fault codes after reassembly. Wiring routing diagrams for this specific model are not documented in open sources, so the general Toyota principle is described below.
Parts
3| № | Part |
|---|---|
| 01 | SRS repair connectorif damagedFind on Amazon → |
| 02 | SRS repair harnessif damagedFind on Amazon → |
| 03 | Airbags, curtain airbags and seatbelt pretensionersonly those already deployedFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
4Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
11 steps- Turn the ignition off, disconnect the negative battery terminal and wait at least 3 minutes. Toyota's official minimum is 90 seconds, but a longer wait is safer. During this time the capacitors in the SRS control module discharge. Never work on the yellow connectors while the battery is connected.
- Do not insert a resistor, test lamp or tester probe into the SRS connectors, and do not check them with a multimeter. Airbag circuits are sensitive to current. Hold an airbag with the cover facing away from you and your body. Never drop it or lay it face down on the floor.
- Inspect every connector before connecting it. The terminals must not be bent, burned or corroded. The shorting clips inside the airbag connectors must be in place. Replace a damaged connector or harness. Never solder or splice SRS wires.
- Locate the connectors. The driver airbag connects to the clock spring (spiral cable) in the steering column. The passenger airbag connector is in the dashboard area. The side airbags are in the backs of the front seats, and the curtain airbags are under the pillar and headliner trim, with harnesses running along the pillars to the SRS control module. The SRS module is on the transmission tunnel under the center console.
- Connect each connector without force, until it clicks. If it will not seat, check the keying and the position of the secondary lock. Do not force it.
- Then push the yellow secondary lock (connector lock) all the way in so that it secures the connector. Pull on the connector by hand. It must not come apart.
- Route the harnesses as original, through the clips, without tension or pinching. Make sure the harness under the seat cannot be caught by the seat rails and that the clock spring in the steering column is not chafed. Then reinstall the trim.
- If the seats, pillars or steering column were removed, check that the clock spring is centered and that the front wheels are pointing straight ahead. Incorrect centering can tear the cable ribbon.
- Reconnect the negative battery terminal. Close the doors and make sure nobody is inside the vehicle. Then turn the ignition on. The SRS warning light should come on for about 6 seconds and then go out. If it stays on, flashes, or does not come on at all, there is a fault.
- Read the codes with an SRS-capable scan tool and clear them. If the codes return after clearing, find the cause (most often a loose connector, an unclosed secondary lock, an incorrectly connected airbag or a damaged harness). Disconnect the battery again, wait, and check the circuit.
- If the passenger seat has an occupant detection sensor (depends on the market), its connector is separate. After work on the seat it also needs to be checked and may need calibration with special equipment.
Common mistakes and warnings
- Working with airbags is dangerous: accidental deployment can cause injury
- If you have no experience, leave the job to a repair shop
- A vehicle with the SRS light on must not be considered safe, because the airbags may not deploy in a crash
- Codes that will not clear and the coding of new modules require dealer equipment
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →