https://autopapyrus.com/catalog/toyota/premio/guides/idle-speed-check/
Toyota Premio 1.8 Valvematic 2ZR-FAE (2009): Idle Speed Check
The 2ZR-FAE has no adjustable idle screw. The ECU controls idle speed through the electronic throttle, so the check comes down to reading engine speed on a scan tool with the engine warmed up. Reference value for a warm engine with no load: about 600-700 rpm. Verify the exact spec in the manufacturer's service manual.
Parts
6| № | Part |
|---|---|
| 01 | Electronic throttle body (complete assembly)if faultyFind on Amazon → |
| 02 | Air filterif faultyFind on Amazon → |
| 03 | Spark plugsif faultyFind on Amazon → |
| 04 | MAF sensorif faultyFind on Amazon → |
| 05 | Vacuum system hosesif faultyFind on Amazon → |
| 06 | Intake ductif faultyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
3Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
11 steps- Prepare the vehicle. Set the parking brake and put the selector in P (automatic) or neutral (manual). Turn off all electrical loads: A/C, rear window defogger, headlights, and the stereo at high volume. Keep the steering wheel straight.
- Warm the engine to operating temperature. Coolant should be about 80-90 °C, and the radiator fan usually cycles on at least once. On a cold engine, idle speed is temporarily high (up to 1000-2000 rpm at startup). This is normal and not a fault.
- Connect the scan tool to the OBD-II diagnostic port under the dashboard, to the left of the driver. Turn the ignition on and start the engine.
- Open Live Data and display these parameters: Engine Speed (rpm), Coolant Temp, Throttle Position, MAF, and Short/Long Fuel Trim. The instrument cluster tachometer is only good for a rough estimate.
- Let the engine idle for 1-2 minutes and record the engine speed. It should be steady (fluctuating by no more than a few dozen rpm) and in the range of 600-700 rpm. For a clean reading, do not touch the accelerator pedal.
- Turn on the A/C and watch the response. The ECU should raise idle speed by a few dozen to about 100 rpm, with no dip and no stalling. Then, on an automatic, shift into D with the brake pedal pressed and check how well the engine holds speed under load.
- Check throttle response. Briefly blip the throttle and release it. Engine speed should return smoothly to idle within 2-3 seconds, without hanging at 1200-1500 rpm and without dropping below the normal idle speed.
- Read the trouble codes. Codes for the throttle, MAF, oxygen sensor, incorrect air-fuel mixture, or misfires can explain a fluctuating idle. If any codes are present, fix their cause first.
- If idle speed is too high or fluctuating, check the following: - vacuum leaks (the duct between the MAF sensor and the throttle body, vacuum hoses, the crankcase ventilation hose); - a dirty throttle body (clean it with a cleaner made for electronic throttles, with the ignition off. Do not move the throttle plate with your finger, because the resistance of the return spring can damage the actuator); - the condition of the spark plugs and air filter; - battery charge and alternator operation.
- After cleaning the throttle body or disconnecting the battery, the ECU loses its idle learning. Warm up the engine, let it idle for about 10 minutes with no electrical loads, and then take a short drive. If idle speed still fluctuates, a Throttle Body Relearn procedure is needed using a scan tool. Take the car to a repair shop with the proper equipment.
- To re-evaluate, clear the codes with the scan tool, warm up the engine, and repeat the measurement. If idle speed has not returned to normal and no codes appear, the cause is most likely the throttle body or a vacuum leak.
Common mistakes and warnings
- Work in a well-ventilated area
- With the engine running, keep your hands and rags away from the accessory drive belt and the radiator fan
- The nominal idle speed and tolerances for this engine are approximate, so verify the exact value in the manufacturer's service manual
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →